Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301869 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 85720E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B203475E19
0.133,0.087 0.291,0.227 0.158,0.140 10 *a 1.619,2.129 1.947,2.269 0.328,0.140 10 GND 1.45,2.951 1.910,3.096 0.459,0.144 10 DOWN 0.371,2.951 0.582,3.089 0.211,0.137 10 UP 0.411,2.129 0.523,2.269 0.112,0.140 10 B 1.216,2.527 1.216,2.213 1.216,2.213 1.614,2.213 false 1.09,2.519 1.086,2.212 1.086,2.212 0.54,2.212 false 1.231,2.711 1.231,3.037 1.231,3.037 1.459,3.037 false 1.049,2.711 1.049,3.033 1.049,3.033 0.617,3.033 false 2.96,1.857 3.118,1.997 0.158,0.140 10 *b 2.333,2.33 2.491,2.469 0.158,0.140 10 *c

Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 10 (UP) within 1 second.


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect the negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Counterclockwise
*c Clockwise

If the result is not as specified, replace the power window regulator motor assembly LH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85710F 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B203474E16
0.058,0.06 0.235,0.214 0.177,0.154 10 *a 2.677,2.93 3.137,3.068 0.460,0.139 10 DOWN 2.849,2.105 3.179,2.243 0.329,0.139 10 GND 1.663,2.105 1.776,2.243 0.112,0.139 10 B 1.564,2.93 1.776,3.068 0.212,0.139 10 UP 2.413,2.5 2.413,2.184 2.413,2.184 2.834,2.184 false 2.298,2.5 2.298,2.184 2.298,2.184 1.781,2.184 false 2.272,2.709 2.272,3.003 2.272,3.003 1.824,3.003 false 2.439,2.701 2.439,2.997 2.439,2.997 2.679,2.997 false 0.299,1.813 0.462,1.967 0.163,0.154 10 *b 0.952,2.242 1.115,2.397 0.163,0.154 10 *c

Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 10 (UP) within 1 second.


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 7 (DOWN) within 1 second.


Motor gear rotates clockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise

If the result is not as specified, replace the power window regulator motor assembly RH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.