Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › from 2014.11
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301869 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 85720E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
E292072E18
1.469,3.792 0.917,3.792 false 2.51,3.781 1.958,3.781 false 1.521,3.417 0.969,3.417 false 2.448,3.417 1.896,3.417 false 0.292,2.563 0.448,2.74 0.156,0.177 10 false *a 0.781,3.323 0.938,3.5 0.156,0.177 10 false B 2.479,3.333 2.802,3.51 0.323,0.177 10 false GND 0.646,3.729 0.854,3.906 0.208,0.177 10 false UP 2.552,3.688 3.01,3.865 0.458,0.177 10 false DOWN 2.771,1.313 2.979,1.49 0.208,0.177 10 false *b 2.25,2.177 2.458,2.354 0.208,0.177 10 false *c

Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect the negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).


Motor gear rotates counterclockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Counterclockwise
*c Clockwise

If the result is not as specified, replace the power window regulator motor assembly LH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85710F 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
E292071E17
1.469,3.792 0.917,3.792 false 2.51,3.792 1.958,3.792 false 1.521,3.417 0.969,3.417 false 2.448,3.417 1.896,3.417 false 0.292,2.563 0.448,2.74 0.156,0.177 10 false *a 0.781,3.323 0.938,3.5 0.156,0.177 10 false B 2.49,3.333 2.813,3.51 0.323,0.177 10 false GND 0.646,3.708 0.854,3.885 0.208,0.177 10 false UP 2.542,3.708 3,3.885 0.458,0.177 10 false DOWN 1.167,2.198 1.375,2.375 0.208,0.177 10 false *b 0.625,1.292 0.833,1.469 0.208,0.177 10 false *c

Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).


Motor gear rotates clockwise


Text in Illustration
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Counterclockwise
*c Clockwise

If the result is not as specified, replace the power window regulator motor assembly RH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.