64886
1.REMOVE BACK WINDOW GLASS CHANNEL LH
64885A
2.REMOVE BACK WINDOW GLASS CHANNEL RH
67939B
3.REMOVE BACK DOOR CENTER GARNISH
4.REMOVE REAR SPOILER ASSEMBLY
67938A
5.REMOVE BACK DOOR SIDE GARNISH LH
67937B
6.REMOVE BACK DOOR SIDE GARNISH RH
67750
7.REMOVE BACK DOOR TRIM BOARD ASSEMBLY
85292A
8.REMOVE REAR WIPER ARM HEAD CAP
9.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY
85143R
10.REMOVE REAR WIPER MOTOR GROMMET
85110R
11.REMOVE REAR WIPER MOTOR ASSEMBLY
68131
12.REMOVE BACK DOOR GLASS
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
| *1 | Protective Tape |
When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.
Place matchmarks on the back door glass and vehicle body on the locations indicated in the illustration.
| *1 | Matchmark |
Matchmarks are not necessary if the back door glass is not going to be reused.
Disconnect the 2 connectors.
Pass a piano wire between the vehicle body and back door glass from the interior as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.
Cut off the adhesive by pulling the piano wire around the back door glass.
Leave as much adhesive on the vehicle body as possible when removing the back door glass.
Using suction cups, disengage the 2 clips and remove the back door glass.
64818C
13.REMOVE NO. 1 BACK WINDOW GLASS SPACER
When reusing the back door glass:
Using a scraper, remove the No. 1 back window glass spacer.
| *A | Back Side |
Be careful not to damage the back door glass.
Be sure to replace the No. 1 back window glass spacer with a new one.
64819
14.REMOVE NO. 2 BACK WINDOW GLASS SPACER
Use the same procedure as for the RH side.
75575D
15.REMOVE BACK WINDOW LOWER MOULDING
When reusing the back door glass:
Using a scraper, remove the back window lower moulding.
| *A | Back Side |
Be careful not to damage the back door glass.
Be sure to replace the back window lower moulding with a new one.
75573G
16.REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING RH
When reusing the back door glass:
Using a scraper, remove the No. 1 back window outside moulding RH.
| *A | Back Side |
Be careful not to damage the back door glass.
Be sure to replace the No. 1 back window outside moulding RH with a new one.
75574C
17.REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING LH
Use the same procedure as for the RH side.
68294A
18.REMOVE BACK DOOR GLASS ADHESIVE DAM
When reusing the back door glass:
Using a scraper, remove the back door glass adhesive dam.
| *A | Back Side |
Be careful not to damage the back door glass.
Be sure to replace the back door glass adhesive dam with a new one.
68131
19.CLEAN BACK DOOR GLASS
Using a scraper, remove the adhesive tape and adhesive sticking to the back door glass.
Be careful not to damage the back door glass.
Clean the outer circumference of the back door glass with a non-residue solvent.
Do not touch the back door glass surface after cleaning it.
Even if using a new back door glass, clean the back door glass with a non-residue solvent.
20.CLEAN VEHICLE BODY
Using a scraper, remove the moulding and adhesive from the back window fix glass.
| *1 | Adhesive |
| *2 | Vehicle Body |
Clean and shape the contact surfaces of the vehicle body.
Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.
Be careful not to damage the vehicle body.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.