Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS › 2014.11–2016.05
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301876 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


PROCEDURE

Hide 62720A 1.CLEAN QUARTER WINDOW ASSEMBLY

a.

Clean the outer edges of the quarter window assembly with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass or clips.




Hide 62720A 2.INSTALL QUARTER WINDOW ASSEMBLY

a.

Using a brush or a sponge, apply body primer to the exposed part of the vehicle body.

B283214E03
6.365,0.948 6.49,0.677 false 6.083,2.573 6.385,2.615 false 4.563,1.146 4.292,1.083 false 0.906,0.406 1.198,0.281 false 2.781,0.969 2.677,1.115 false 6.052,1.042 5.844,0.99 false 4.885,2.438 5.031,2.688 false 4.135,2.427 4.271,2.677 false 1.698,1.688 1.823,1.865 0.125,0.177 10 false A 1.594,2.094 1.719,2.271 0.125,0.177 10 false A 0.708,2.594 0.823,2.74 0.115,0.146 10 false B 1.396,2.229 1.51,2.375 0.115,0.146 10 true B 0.896,2.771 1.021,2.917 0.125,0.146 10 false C 2.771,2.781 2.938,2.948 0.167,0.167 10 false D 2.573,2.406 2.74,2.573 0.167,0.167 10 false D 3.948,0.396 4.313,0.563 0.365,0.167 10 false A - A 5.625,0.396 6.031,0.573 0.406,0.177 10 false B - B 3.948,2.042 4.375,2.25 0.427,0.208 10 false C - C 5.625,2.042 6.01,2.271 0.385,0.229 10 false D - D 4.146,1.021 4.302,1.167 0.156,0.146 10 false *4 6.5,0.615 6.646,0.76 0.146,0.146 10 false *4 6.396,2.552 6.542,2.698 0.146,0.146 10 false *4 0.313,3.573 0.469,3.719 0.156,0.146 10 false *1 1.208,0.219 1.365,0.365 0.156,0.146 10 false *2 2.615,1.125 2.76,1.26 0.146,0.135 10 false *3 1.469,2.5 1.594,2.646 0.125,0.146 10 false C 1.688,0.021 1.844,0.167 0.156,0.146 10 false *a 2.531,0.021 2.688,0.167 0.156,0.146 10 false *b 5.698,0.927 5.844,1.073 0.146,0.146 10 false *4 4.74,2.385 4.885,2.531 0.146,0.146 10 false *4 3.979,2.375 4.125,2.521 0.146,0.146 10 false *4

Text in Illustration
*1 Body Primer *2 Brush
*3 Adhesive *4 Edge of Curved Surface
*a CORRECT *b WRONG

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.




b.

Using a brush or a sponge, apply glass primer to the contact surface of a new quarter window assembly.

B274981E01
1.63,5.682 1.787,5.831 0.157,0.149 10 *2 0.428,6.624 0.585,6.773 0.157,0.149 10 *1 5.494,1.21 5.831,1.359 0.337,0.149 10 B - B 3.637,3.774 3.979,3.923 0.342,0.149 10 C - C 5.494,3.774 5.836,3.923 0.342,0.149 10 D - D 3.637,1.21 3.974,1.359 0.337,0.149 10 A - A 2.288,4.515 2.404,4.664 0.116,0.149 10 B 2.137,4.739 2.267,4.888 0.130,0.149 10 C 1.345,4.978 1.474,5.127 0.130,0.149 10 D 1.199,4.006 1.314,4.155 0.116,0.149 10 A 1.261,4.383 1.377,4.532 0.116,0.149 10 A 2.8,4.753 2.915,4.902 0.116,0.149 10 B 2.662,4.977 2.792,5.126 0.130,0.149 10 C 1.157,5.277 1.286,5.426 0.130,0.149 10 D 0.348,6.608 0.408,6.756 0.060,0.149 10 : 0.856,2.817 1.329,2.584 false 1.701,5.676 1.724,5.356 false 0.689,2.747 0.846,2.896 0.157,0.149 10 *3 4.788,1.855 4.904,2.004 0.116,0.149 10 a 4.325,4.447 4.440,4.596 0.116,0.149 10 c 0.147,0.134 0.346,0.297 0.199,0.163 10 *A 6.286,1.87 6.402,2.019 0.116,0.149 10 b 5.884,4.856 6.000,5.005 0.116,0.149 10 d 2.824,2.351 2.557,2.209 false 2.839,2.292 2.996,2.441 0.157,0.149 10 *3

Text in Illustration
*A Back Side - -
*1 Glass Primer *2 Adhesive Center
*3 Ceramic Notch - -

Area Dimension
a 11.0 mm (0.433 in.) or more
b 13.0 mm (0.512 in.) or more
c 21.0 mm (0.827 in.) or more
d 12.3 mm (0.484 in.) or more

HINT:

If an area other than that specified is coated by accident, wipe off the glass primer with a non-residue solvent before it dries.


NOTICE:
·

To prevent the glass from breaking at low temperatures, ensure that no glass primer adheres to the contact surface between the moulding and glass during application.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.

·

Do not apply too much glass primer.




c.

Apply adhesive to the quarter window assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E03
0.496,0.546 0.650,0.739 0.154,0.193 10 a 1.339,1.361 1.494,1.554 0.154,0.193 10 a 1.142,0.852 1.296,1.045 0.154,0.193 10 b 0.75,0.937 0.905,1.130 0.154,0.193 10 b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)



ii.

Load the sealer gun with cartridge.


iii.

Apply adhesive to the quarter window glass as shown in the illustration.

B274982E01
1.63,5.682 1.787,5.831 0.157,0.149 10 *2 0.428,6.624 0.585,6.773 0.157,0.149 10 *1 5.494,1.21 5.831,1.359 0.337,0.149 10 B - B 3.637,3.774 3.979,3.923 0.342,0.149 10 C - C 5.494,3.774 5.836,3.923 0.342,0.149 10 D - D 3.637,1.21 3.974,1.359 0.337,0.149 10 A - A 2.288,4.515 2.404,4.664 0.116,0.149 10 B 2.137,4.739 2.267,4.888 0.130,0.149 10 C 1.345,4.978 1.474,5.127 0.130,0.149 10 D 1.199,4.006 1.314,4.155 0.116,0.149 10 A 1.261,4.383 1.377,4.532 0.116,0.149 10 A 2.8,4.753 2.915,4.902 0.116,0.149 10 B 2.662,4.977 2.792,5.126 0.130,0.149 10 C 1.157,5.277 1.286,5.426 0.130,0.149 10 D 0.348,6.608 0.408,6.756 0.060,0.149 10 : 0.856,2.817 1.329,2.584 false 1.701,5.676 1.724,5.356 false 0.689,2.747 0.846,2.896 0.157,0.149 10 *3 4.103,1.841 4.219,1.990 0.116,0.149 10 a 4.823,5.085 4.939,5.234 0.116,0.149 10 c 0.147,0.134 0.346,0.297 0.199,0.163 10 *A 6.357,2.711 6.473,2.860 0.116,0.149 10 b 6.685,4.997 6.800,5.146 0.116,0.149 10 e 2.824,2.351 2.557,2.209 false 2.839,2.292 2.996,2.441 0.157,0.149 10 *3 4.649,5.249 4.765,5.398 0.116,0.149 10 d

Text in Illustration
*A Back Side - -
*1 Adhesive *2 Adhesive Center
*3 Ceramic Notch - -

Standard Dimension:
Area Dimension
a 4.0 mm (0.157 in.)
b 6.4 mm (0.252 in.)
c 6.0 mm (0.236 in.)
d 8.0 mm (0.315 in.)
e 5.3 mm (0.209 in.)




d.

Install a new quarter window assembly to the vehicle body.

i.

Engage the 3 clips to install the quarter window glass assembly.


ii.

Hold the quarter window assembly in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:
·

Allow the glass primer to dry for 3 minutes or more.

·

Check that the clips are attached to the body correctly.

·

Check the clearance between the body and glass.




iii.

Lightly press the outer surface of the glass to ensure that the glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



iv.

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive onto the glass rim.


NOTICE:

Do not drive the vehicle within the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 3.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 62480A 4.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY

Hide 64740C 5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY

Hide 81250 6.INSTALL NO. 2 ROOM LIGHT ASSEMBLY (for LH Side)

Hide 73570 7.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY (for Lower Side)

Hide 73370C 8.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

Hide 55548C 9.INSTALL NO. 2 CUP HOLDER (for LH Side)

Hide 55548C 10.INSTALL NO. 1 CUP HOLDER (for RH Side)

Hide 64713F 11.INSTALL FRONT DECK SIDE TRIM COVER

Hide 58460D 12.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 62332A 14.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 64910J 17.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 23.INSTALL REAR NO. 2 SEAT ASSEMBLY