Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS › from 2016.05
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301876 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 64910J 7.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 62332A 10.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 58460D 12.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 64713F 13.REMOVE FRONT DECK SIDE TRIM COVER

Hide 55548C 14.REMOVE NO. 2 CUP HOLDER (for LH Side)

Hide 55548C 15.REMOVE NO. 1 CUP HOLDER (for RH Side)

Hide 73370C 16.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

Hide 73570 17.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY (for Lower Side)

Hide 81250 18.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (for LH Side)

Hide 64740C 19.REMOVE DECK TRIM SIDE PANEL ASSEMBLY

Hide 62480A 20.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

Hide 62720A 21.REMOVE QUARTER WINDOW ASSEMBLY

a.
B274978E01
0.457,1.095 0.615,1.244 0.157,0.149 10 *1 0.645,1.176 1.012,1.062 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

Text in Illustration
*1 Protective Tape


b.
B274979E01
0.532,1.265 0.689,1.414 0.157,0.149 10 *1 0.716,1.346 1.108,1.211 false

Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.

HINT:

Ensure not to interfere with the clips when passing the piano wire.


Text in Illustration
*1 Piano Wire


c.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.

NOTICE:

When separating the quarter window assembly from the vehicle, be careful not to damage the paint or interior and exterior ornaments.



d.

Cut off the adhesive by pulling the piano wire around the quarter window assembly.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



e.
B274980

Disengage the 3 clips.


f.

Using suction cups, remove the glass.

NOTICE:

Be careful not to drop the glass.



Hide 22.CLEAN VEHICLE BODY

a.
B106081E36
0.49,1.302 0.771,0.729 0.771,0.729 0.948,0.729 false 2.281,1.438 2.563,0.74 2.563,0.74 2.729,0.74 false 2.427,1.615 2.427,1.792 false 0.802,1.563 0.802,1.75 false 1,0.656 1.24,0.854 0.24,0.198 10 false *1 2.781,0.667 3.021,0.865 0.24,0.198 10 false *1 0.74,1.802 0.979,2 0.24,0.198 10 false *2 2.365,1.833 2.604,2.031 0.24,0.198 10 false *2

Clean and shape the contact surfaces of the vehicle body.

Text in Illustration
*1 Adhesive
*2 Vehicle Body

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.




b.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.