Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM2070E _59 Vehicle Exterior _061950 DOOR / HATCH _0301880 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B228782E01
2.455,0.051 2.648,0.198 0.193,0.147 10 *2 0.817,0.051 1.010,0.198 0.193,0.147 10 *1

Text in Illustration
*1 Centering Bolt
*2 Standard Bolt

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas *a through *o are within each standard range.

B276147E01
1.06,1.939 1.244,2.103 0.184,0.164 10 *a 1.597,1.603 1.781,1.767 0.184,0.164 10 *b 2.49,1.094 2.675,1.257 0.184,0.164 10 *c 2.333,0.542 2.517,0.705 0.184,0.164 10 *d 4.026,1.089 4.211,1.252 0.184,0.164 10 *e 3.876,0.544 4.061,0.707 0.184,0.164 10 *f 5.736,1.951 5.921,2.114 0.184,0.164 10 *g 6.068,4.619 6.252,4.783 0.184,0.164 10 *i 6.367,4.06 6.551,4.223 0.184,0.164 10 *j 4.625,5.132 4.809,5.295 0.184,0.164 10 *k 4.843,4.564 5.027,4.728 0.184,0.164 10 *l 2.311,4.712 2.523,4.875 0.212,0.164 10 *m 1.278,4.457 1.462,4.621 0.184,0.164 10 *n 0.77,4.205 0.955,4.369 0.184,0.164 10 *o 5.445,1.358 5.629,1.522 0.184,0.164 10 *h

Standard Clearance
Area Measurement Area Measurement
*a 2.5 to 6.5 mm (0.0984 to 0.256 in.) *b -2.0 to 2.0 mm (-0.0787 to 0.0787 in.)
*c 5.57 to 8.57 mm (0.219 to 0.337 in.) *d 3.57 to 6.57 mm (0.141 to 0.259 in.)
*e 5.17 to 8.17 mm (0.204 to 0.322 in.) *f 3.57 to 6.57 mm (0.141 to 0.259 in.)
*g 4.22 to 8.22 mm (0.166 to 0.324 in.) *h 1.52 to 5.52 mm (0.0598 to 0.217 in.)
*i 2.5 to 5.5 mm (0.0984 to 0.217 in.) *j -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
*k 2.5 to 5.5 mm (0.0984 to 0.217 in.) *l -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
*m 3.8 to 7.8 mm (0.150 to 0.307 in.) *n 3.0 to 6.0 mm (0.118 to 0.236 in.)
*o -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -


Hide 2.ADJUST REAR DOOR

NOTICE:

Make sure to turn the power switch off when adjusting door lock strikers.


a.
B275234

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B275235

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)