Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2013.08–2014.11
RM2070E _59 Vehicle Exterior _061950 DOOR / HATCH _0301880 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 7.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 69284D 8.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B282945

Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.


Hide 9.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.
B282946

Using a moulding remover, disengage the clip, 10 claws and 5 guides.


b.

Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.


Hide 74262 10.REMOVE REAR DOOR ARMREST COVER

a.
B282947

Remove the rear door armrest cover.


Hide 67604 11.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B282948E01
2.637,0.904 2.806,1.056 0.168,0.152 10 *1 2.822,1.002 3.04,1.075 false

Put protective tape around the rear door panel.

Text in Illustration
*1 Protective Tape


b.
B282949

Remove the 2 screws.


c.

Using a clip remover, disengage the 9 clips.


d.

Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.


e.

Raise the rear door trim board sub-assembly and disconnect the rear door trim board sub-assembly with the rear door inner glass weatherstrip.


f.

for 8 Speakers:

i.

Disconnect the connector.



g.
B282950

Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door trim board sub-assembly.


Hide 68174A 12.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

a.
B282952

Disengage the 7 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.


Hide 65908D 13.REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B310467

Remove the 9 screws and rear curtain sub-assembly.


Hide 69206C 14.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B282951

Using a screwdriver, disengage the 2 claws to remove the rear door inside handle sub-assembly.


Hide 86160Y 15.REMOVE REAR NO. 2 SPEAKER ASSEMBLY (for 8 Speakers)

Hide 67628 17.REMOVE REAR DOOR TRIM BRACKET

a.
B282954

Remove the 2 screws and rear door trim bracket.


Hide 67842E 18.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B282955

Disconnect the 2 connectors.


b.

Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 68640A 19.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B282956

Remove the bolt, 2 nuts and rear door check assembly.


Hide 67872 20.REMOVE REAR DOOR WEATHERSTRIP

a.
B282957

Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.


Hide 68152C 21.REMOVE REAR DOOR GLASS RUN

a.
B282958

Remove the rear door glass run.


Hide 67408D 22.REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY

a.
B282959

Remove the screw.


b.

Remove the bolt and rear door window guide sub-assembly.


Hide 67488C 23.REMOVE REAR DOOR REAR GUIDE SEAL

a.

Remove the 3 screws.

B282960


b.

Remove the rear door rear guide seal as shown in the illustration.


Hide 68104 24.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the rear power window regulator motor connector.


c.

Connect the rear power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


d.

Disconnect the rear power window regulator switch assembly and rear power window regulator motor connector.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


f.
B282961

Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.

NOTICE:
·

After the bolts are removed, do not allow the door glass to fall.

·

Do not damage the door glass.




Hide 25.REMOVE REAR DOOR POWER WINDOW REGULATOR ASSEMBLY

a.
B282962E01
1.663,1.095 1.816,1.248 0.153,0.152 10 *1 1.843,1.198 2.189,1.299 false

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door power window regulator assembly may fall and cause damage.



b.

Remove the 5 bolts.


c.

Remove the rear door power window regulator assembly.


d.

Remove the temporary bolt from the rear door power window regulator assembly.


Hide 85720E 26.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B282963

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.


Hide 69060A 27.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

a.
B282563E01
0.351,2.56 0.582,2.776 0.232,0.215 10 *1 1.394,2.461 0.541,2.65 false

Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.

Text in Illustration
*1 Release Plate


c.

When reusing the rear door lock with motor assembly:

i.
B282965

Remove the door lock wiring harness seal from the rear door lock with motor assembly.



Hide 69740D 28.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B282966

Using a screwdriver, disengage the claw as shown in the illustration.


b.
B282967

Remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69740D 29.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B310468

Using a screwdriver, disengage the claw as shown in the illustration.


b.
B310470

Remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69780B 30.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B314466

Using a screwdriver, disengage the 3 claws as shown in the illustration.


b.
B282969

Remove the rear door inside locking cable assembly as shown in the illustration.


Hide 69780B 31.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B310472

Using a screwdriver, disengage the 3 claws as shown in the illustration.


b.
B310474

Remove the rear door inside locking cable assembly as shown in the illustration.


Hide 69227L 32.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B282970

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.



b.

Disengage the claw to remove the rear door outside handle cover.


Hide 69240 33.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B282971

Move the lever in the direction indicated by the arrow in the illustration.


b.
B282972

Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

NOTICE:

The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.



c.
B282973

Remove the rear door outside handle assembly as shown in the illustration.


Hide 69241G 34.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B282974

Disengage the 3 claws to remove the rear door front outside handle pad.


Hide 69242G 35.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B282975

Disengage the 2 claws to remove the rear door rear outside handle pad.


Hide 69204A 36.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B282976E01
0.131,0.082 0.315,0.255 0.185,0.173 10 *a 0.131,2.249 0.315,2.422 0.185,0.173 10 *b

Using a T30 "TORX" socket wrench, loosen the screw.

Text in Illustration
*a Outside
*b Inside


b.

Slide the rear door outside handle frame sub-assembly to disengage the door handle nut and claw of the rear door outside handle frame sub-assembly, and then remove the rear door outside handle frame sub-assembly.


Hide 67003C 37.REMOVE REAR DOOR PANEL CUSHION

a.
B282977

Disengage the 2 claws to remove the 2 rear door panel cushions.


Hide 67674A 38.REMOVE REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)

a.
B282953

Disengage the clip to remove the rear door frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.



Hide 67676C 39.REMOVE REAR DOOR NO. 2 FRAME GARNISH (w/o Rear Door Sunshade)

a.
B314486

Disengage the clip to remove the rear door No. 2 frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing the rear door No. 2 frame garnish.



Hide 67674A 40.REMOVE REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)

a.
B314404

Disengage the clip to remove the rear door frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.



Hide 67676C 41.REMOVE REAR DOOR NO. 2 FRAME GARNISH (w/ Rear Door Sunshade)

a.
B314405

Disengage the clip to remove the rear door No. 2 frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing the rear door No. 2 frame garnish.



Hide 75740 42.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 75762A 43.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING