Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM2070E _59 Vehicle Exterior _061951 MIRROR (EXT) _0301890 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY

a.

Check the mirror select switch and mirror surface adjust switch. (for RHD and w/o Double Locking System)

i.
B254629E17
0.525,2.808 0.680,2.951 0.155,0.142 10 *a 2.911,4.188 3.130,4.333 0.219,0.145 10 HR 2.505,4.188 2.717,4.333 0.212,0.145 10 VR 2.127,4.188 2.315,4.333 0.189,0.145 10 VL 1.755,4.188 1.954,4.333 0.199,0.145 10 HL 1.268,4.188 1.482,4.333 0.215,0.145 10 M+ 1.03,4.188 1.141,4.333 0.111,0.145 10 E 0.637,4.188 0.752,4.333 0.116,0.145 10 B 1.702,3.688 1.842,4.159 false 1.596,3.688 1.391,4.15 false 1.484,3.688 1.097,4.149 false 1.382,3.688 0.744,4.147 false 1.817,3.688 2.162,4.159 false 1.926,3.688 2.536,4.156 false 2.037,3.688 2.967,4.153 false 1.555,0.866 1.555,0.342 1.555,0.342 1.377,0.342 false 1.172,0.253 1.328,0.395 0.156,0.142 10 *1 1.714,1.876 1.714,2.38 1.714,2.38 1.981,2.38 false 2.032,2.307 2.188,2.449 0.156,0.142 10 *2

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


Text in Illustration
*1 Mirror select switch
*2 Mirror surface adjust switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch. (for LHD or w/ Double Locking System)

i.
B314504E03
0.524,2.413 0.704,2.569 0.180,0.156 10 *a 2.905,4.033 3.124,4.178 0.219,0.145 10 HR 2.499,4.033 2.711,4.178 0.212,0.145 10 VR 2.138,4.033 2.327,4.178 0.189,0.145 10 VL 1.784,4.033 1.983,4.178 0.199,0.145 10 HL 1.331,4.033 1.545,4.178 0.215,0.145 10 M+ 1.093,4.033 1.204,4.178 0.111,0.145 10 E 0.666,4.033 0.781,4.178 0.116,0.145 10 B 1.869,3.533 1.869,4.004 false 1.625,3.533 1.454,3.995 false 1.512,3.533 1.16,3.994 false 1.273,3.533 0.773,3.992 false 1.983,3.533 2.173,4.004 false 2.092,3.533 2.531,4.001 false 2.203,3.533 2.944,3.998 false 1.539,0.893 1.539,0.368 1.539,0.368 1.361,0.368 false 1.157,0.28 1.312,0.422 0.156,0.142 10 *1 1.698,1.902 1.698,2.407 1.698,2.407 1.965,2.407 false 2.016,2.333 2.172,2.475 0.156,0.142 10 *2

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
16 (VL) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
16 (VL) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
15 (VR) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
15 (VR) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


Text in Illustration
*1 Mirror select switch
*2 Mirror surface adjust switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror retract switch. (for RHD and w/o Double Locking System)

i.
B254629E19
1.479,3.667 1.573,4.135 false 1.375,3.677 1.25,4.135 false 1.26,3.677 0.979,4.135 false 1.156,3.677 0.542,4.135 false 2.01,0.865 2.01,0.396 2.01,0.396 2.188,0.396 false 0.615,2.635 0.771,2.781 0.156,0.146 10 false *a 0.813,4.156 1.042,4.302 0.229,0.146 10 false MR 0.406,4.156 0.635,4.302 0.229,0.146 10 false MF 1.531,4.156 1.646,4.302 0.115,0.146 10 false E 1.188,4.156 1.302,4.302 0.115,0.146 10 false B 2.24,0.323 2.396,0.469 0.156,0.146 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
10 (MF) - 7 (E) Mirror retract switch retract position Below 1 Ω
9 (MR) - 8 (B) Below 1 Ω
10 (MF) - 8 (B) Mirror retract switch return position Below 1 Ω
9 (MR) - 7 (E) Below 1 Ω


Text in Illustration
*1 Mirror retract switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.



d.

Check the mirror retract switch. (for LHD or w/ Double Locking System)

i.
B314504E04
0.563,2.509 0.729,2.664 0.166,0.154 10 *a 0.852,3.991 1.085,4.136 0.233,0.145 10 MR 0.448,3.991 0.673,4.136 0.225,0.145 10 MF 1.856,3.991 1.967,4.136 0.111,0.145 10 E 1.377,3.991 1.493,4.136 0.116,0.145 10 B 1.519,3.526 1.87,3.991 false 1.28,3.532 1.413,3.991 false 1.165,3.532 1.04,3.991 false 1.055,3.532 0.592,3.991 false 2.004,0.887 2.004,0.424 2.004,0.424 2.188,0.424 false 2.229,0.344 2.389,0.491 0.161,0.147 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
24 (MF) - 20 (E) Mirror retract switch retract position Below 1 Ω
23 (MR) - 22 (B) Below 1 Ω
24 (MF) - 22 (B) Mirror retract switch return position Below 1 Ω
23 (MR) - 20 (E) Below 1 Ω


Text in Illustration
*1 Mirror retract switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.