Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301891 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK WINDSHIELD WIPER RELAY ASSEMBLY (w/ Auto Wiper System)


U191216E02
3.469,0.813 3.792,0.969 0.323,0.156 10 false L146

a.

Disconnect the L146 windshield wiper relay assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L146-2 (IG) - Body ground B - Body ground Power switch on (IG) signal (Power source circuit) Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
L146-8 (VR2) - L146-21 (VR1) W - L Adjusting volume circuit Windshield wiper switch adjusting ring* changed 0 to 231 Ω
L146-12 (E) - Body ground W-B - Body ground Body ground Always Below 1 Ω
L146-16 (WIG) - Body ground BE - Body ground Signal power source circuit Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
L146-25 (W) - Body ground B - Body ground Front washer switch circuit Front washer switch on Below 1 Ω
Front washer switch off 10 kΩ or higher

HINT:

*: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.


If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the L146 windshield wiper relay assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L146-1 (+SM) - Body ground G - Body ground Front wiper motor position detection signal Front wiper motor in low or high operation Below 1 V ←→ 11 to 14 V
Front wiper motor off Below 1 V
L146-3 (C1) - L146-5 (C0) V - Y Front wiper switch AUTO signal circuit Power switch on (IG), front wiper switch in AUTO Below 1 V
Power switch on (IG), front wiper switch off 11 to 14 V
L146-10 (+1) - Body ground G - Body ground Front wiper motor low speed signal circuit Front wiper motor in low operation 11 to 14 V
Front wiper motor off Below 1 V
L146-11 (+2) - Body ground L - Body ground Front wiper motor high speed signal circuit Front wiper motor in high operation 11 to 14 V
Front wiper motor off Below 1 V
L146-14 (MPX1) - Body ground Y - Body ground Rain sensor signal Power switch on (IG) Pulse generation
L146-24 (SPD) - Body ground W - Body ground Speed signal Power switch on (IG), wheel being rotated Pulse generation
(See Waveform 1)
L146-25 (W) - Body ground B - Body ground Front washer switch circuit Power switch on (IG), front washer switch on Below 1 V
Power switch on (IG), front washer switch off 11 to 14 V

If the result is not as specified, the windshield wiper relay assembly may have a malfunction.

i.
E267248E13
2.969,1.198 3.323,1.396 0.354,0.198 10 false GND 1.115,1.625 1.323,1.833 0.208,0.208 10 false (A)

Waveform 1 (Reference):

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





CHECK HEADLIGHT CLEANER CONTROL RELAY


a.

Disconnect the A44 headlight cleaner control relay connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

U191215E02
3.406,0.948 3.698,1.104 0.292,0.156 10 false A44

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A44-2 (H) - A44-4 (E) LG - W-B Headlight cleaner switch operation signal Light control switch off and headlight cleaner switch off Below 1 V
Light control switch off and headlight cleaner switch on 11 to 14 V
A44-3 (IG) - A44-4 (E) B - W-B Power switch on (IG) signal (Power source circuit) Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A44-4 (E) - Body ground W-B - Body ground Body ground Always Below 1 Ω
A44-5 (FRWA) - A44-4 (E) R - W-B Front washer switch signal Power switch on (IG)
Front washer switch off
11 to 14 V
Power switch on (IG)
Front washer switch on
Below 1 V
A44-6 (PB) - A44-4 (E) B - W-B Headlight clear motor operation signal Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U190875E02
0.698,2.76 1.021,2.76 false 3.135,7.594 3.427,7.76 0.292,0.167 10 false MB 4.854,6.385 5.146,6.552 0.292,0.167 10 false 2A 1.875,6.375 2.167,6.542 0.292,0.167 10 false 2B 1.167,5.115 1.458,5.281 0.292,0.167 10 false 2D 0.5,1.51 0.792,1.677 0.292,0.167 10 false 2D 3.927,5.146 4.219,5.313 0.292,0.167 10 false 2C 0.49,2.156 0.781,2.323 0.292,0.167 10 false 2C 4.865,3.802 5.156,3.969 0.292,0.167 10 false L7 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.583,5.104 5.875,5.271 0.292,0.167 10 false 2E 5.896,5.104 6.104,5.271 0.208,0.167 10 false *A 6.563,5.115 6.771,5.281 0.208,0.167 10 false *B 2.417,3.802 2.708,3.969 0.292,0.167 10 false L8 0.26,2.563 0.552,2.729 0.292,0.167 10 false 2E 0.573,2.563 0.865,2.729 0.292,0.167 10 false *A 0.583,2.885 0.875,3.052 0.292,0.167 10 false *B 0.26,2.854 0.552,3.021 0.292,0.167 10 false 2F 2.01,1.698 2.302,1.865 0.292,0.167 10 false L7 2,2.063 2.292,2.229 0.292,0.167 10 false L8 6.26,1.531 6.469,1.698 0.208,0.167 10 false 2B 3.708,0.635 4,0.802 0.292,0.167 10 false MB 6.26,2.188 6.469,2.354 0.208,0.167 10 false 2A

Text in Illustration
*A for LHD *B for RHD

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2C-35 - Body ground L - Body ground Low beam headlight signal Power switch on (IG), light control switch in head position Below 1 V
Power switch on (IG), light control switch off 4.2 V or higher