Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2016.05–2020.08
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301891 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Speed Signal Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a vehicle speed signal from the combination meter to control the automatic windshield wiper system.

A voltage of 12 V or 5 V is output from the combination meter assembly and then input to the skid control ECU.

A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly.

Each ECU controls the respective system based on the pulse signal.

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

WIRING DIAGRAM

E309036E01
0.626,1.485 1.749,1.636 1.123,0.151 10 Skid Control ECU 1.429,0.488 1.720,0.639 0.292,0.151 10 SP1 0.626,1.339 0.945,1.520 0.319,0.181 10 A58 1.783,0.488 1.969,0.636 0.187,0.148 10 11 3.048,7.054 4.268,7.216 1.220,0.162 10 Junction Connector 0.275,2.829 2.595,3.205 2.320,0.376 10 Power Management Control ECU 0.275,2.677 0.565,2.841 0.290,0.164 10 L5 0.095,6.83 0.360,6.993 0.265,0.164 10 A48 0.095,6.992 2.407,7.172 2.312,0.180 10 Headlight Leveling ECU Assembly*4 1.334,6.56 1.747,6.715 0.413,0.154 10 SPDR 1.379,2.385 1.779,2.540 0.400,0.154 10 SPDI 1.783,2.385 1.962,2.544 0.180,0.159 10 14 1.785,6.56 1.968,6.719 0.183,0.159 10 16 3.912,2.385 4.348,2.547 0.436,0.162 10 31*2 3.912,2.231 4.348,2.393 0.436,0.162 10 32*1 2.863,2.385 3.082,2.547 0.219,0.162 10 22 1.805,3.874 2.008,4.035 0.203,0.162 10 24 5.307,6.56 5.524,6.722 0.217,0.162 10 11 3.912,3.87 4.295,4.031 0.383,0.162 10 12*2 3.937,3.716 4.320,3.877 0.383,0.162 10 3*1 2.722,3.87 3.104,4.031 0.383,0.162 10 21*2 2.722,3.716 3.104,3.877 0.383,0.162 10 12*1 3.912,6.562 4.295,6.724 0.383,0.162 10 11*2 3.918,6.396 4.301,6.558 0.383,0.162 10 21*1 2.722,6.562 3.104,6.724 0.383,0.162 10 32*2 2.722,6.396 3.104,6.558 0.383,0.162 10 31*1 5.294,0.488 5.598,0.638 0.304,0.150 10 16 5.294,2.385 5.569,2.535 0.275,0.150 10 15 5.542,0.586 5.741,0.736 0.198,0.150 10 SI 5.542,2.496 5.743,2.647 0.201,0.151 10 +S 4.964,2.755 5.296,2.900 0.332,0.145 10 L27 4.964,2.918 7.091,3.149 2.126,0.231 10 Combination Meter Sub-assembly 0.16,4.172 0.520,4.326 0.360,0.153 10 L146 0.154,4.335 2.598,4.604 2.444,0.269 10 Windshield Wiper Relay Assembly*3 4.948,5.666 7.147,5.961 2.200,0.295 10 Navigation Receiver Assembly*6 0.556,7.599 1.372,7.781 0.817,0.182 10 *1: for LHD 1.746,7.599 2.563,7.781 0.817,0.182 10 *2: for RHD 2.923,7.599 4.698,7.781 1.775,0.182 10 *3: w/ Auto Wiper System 5.416,7.599 6.756,7.781 1.340,0.182 10 *4: w/ LED Headlight 0.556,7.988 2.729,8.170 2.173,0.182 10 *5: for Radio and Display Type 2.923,7.988 5.122,8.170 2.199,0.182 10 *6: for Navigation Receiver Type 1.432,3.874 1.760,4.019 0.328,0.145 10 SPD 5.551,6.56 5.880,6.706 0.328,0.145 10 SPD 4.97,5.515 5.245,5.661 0.275,0.145 10 L38 4.503,6.852 4.778,7.005 0.275,0.153 10 L31 4.547,4.129 4.846,4.284 0.299,0.156 10 L35 4.503,7.012 7.135,7.189 2.632,0.177 10 Stereo Component Amplifier Assembly*7 4.547,4.288 7.078,4.463 2.531,0.176 10 Radio and Display Receiver Assembly*5 2.753,7.054 3.067,7.218 0.314,0.164 10 L70 5.547,3.876 5.860,4.037 0.313,0.162 10 SPD 5.309,3.876 5.483,4.037 0.174,0.162 10 17 5.547,5.221 5.860,5.383 0.313,0.162 10 SPD 5.309,5.221 5.483,5.383 0.174,0.162 10 17 5.416,7.988 7.127,8.170 1.710,0.182 10 *7: for 8 Speakers 2.789,5.233 3.172,5.394 0.383,0.162 10 3*2 2.789,5.067 3.172,5.228 0.383,0.162 10 1*1 1.809,5.223 2.012,5.384 0.203,0.162 10 2 0.164,5.533 0.524,5.686 0.360,0.153 10 R41 0.158,5.696 3.083,6.022 2.925,0.327 10 Tire Pressure Warning ECU and Receiver*8 1.436,5.223 1.765,5.368 0.328,0.145 10 SPD 0.556,8.376 2.949,8.557 2.393,0.182 10 *8: w/ Tire Pressure Warning System

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (SPEED SENSOR SIGNAL)
a.
U190824E02
1.271,1.229 1.073,0.698 true 1.135,3.896 1.385,3.896 false 1.073,3.708 1.073,4.031 false 1.438,3.708 1.438,4.031 false 0.135,0.115 0.292,0.271 0.156,0.156 10 false *a 0.938,0.51 1.125,0.667 0.188,0.156 10 false +S 2.781,3.635 3.104,3.792 0.323,0.156 10 false GND 1.146,3.927 1.354,4.083 0.208,0.156 10 false (A) 1.615,0.469 1.917,0.625 0.302,0.156 10 false L27

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER)

NG

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER)
a.

Disconnect the L146 windshield wiper relay assembly connector and L27 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L146-24 (SPD) - L27-15 (+S) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR