Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301892 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Install the No. 1 windshield wiper link washer and windshield wiper motor assembly with the 2 bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 85012A 2.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY

a.

Connect the connector to the windshield wiper motor assembly.


b.

Turn the power switch on (IG).


c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.

Turn the power switch off.


e.

Disconnect the connector from the windshield wiper motor assembly.


f.

Temporarily install the front wiper crank subassembly on the windshield wiper motor assembly with the nut.

E250226E03
4.198,1.323 4.198,2.073 false 3.677,1.302 4.333,0.625 false 3.167,1.323 2.74,2.073 false 4.115,2.073 4.281,2.229 0.167,0.156 10 false *1 2.625,2.073 2.792,2.229 0.167,0.156 10 false *a 4.344,0.5 4.51,0.656 0.167,0.156 10 false *2

Text in Illustration
*1 No. 1 Rod *2 Shaft of the Windshield Wiper Motor Assembly
*a Crank Arm Pivot - -

NOTICE:

Do not operate the windshield wiper motor assembly.



g.

Temporarily install the No. 1 rod on the crank arm pivot of the front wiper crank sub-assembly.


h.

Align the shaft of the windshield wiper motor assembly and crank arm pivot of the front wiper crank sub-assembly with the No. 1 rod as shown in the illustration.

NOTICE:

Do not operate the windshield wiper motor assembly.



i.

Tighten the front wiper crank sub-assembly with the nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


j.
E250227E01
0.334,0.673 0.506,0.845 0.172,0.172 10 *1 1.02,1.009 0.526,0.797 false

Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.

Text in Illustration
*1 Crank Arm Pivot


k.
E250223

Connect the No. 1 rod to the crank arm pivot of the front wiper crank sub-assembly.


Hide 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
E250228

Connect the connector.


b.

Engage the clamp.


c.
E250229E01
1.675,0.225 1.825,0.387 0.150,0.163 10 *1 2.372,0.597 1.839,0.351 false

Engage the grommet as shown in the illustration.

Text in Illustration
*1 Grommet


d.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



e.

Engage the clamp.


Hide 55781E 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 9 guides.

E250219


b.

for LHD:

i.

Engage the 5 claws and 3 guides to install the cowl top ventilator louver sub-assembly.

E250217



c.

for RHD:

i.

Engage the 6 claws and 3 guides to install the cowl top ventilator louver sub-assembly.

E223392



d.

Install the 2 clips.


Hide 55810F 5.INSTALL FRONT VENTILATOR ASSEMBLY

a.
E228578

Engage the 2 claws to install the front ventilator assembly as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


b.
E224627E01
1.928,3.503 2.678,3.503 false 2.679,3.406 2.844,3.565 0.164,0.159 10 *b 0.401,1.455 0.565,1.614 0.164,0.159 10 *a 1.282,1.543 0.583,1.543 false

When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations.

Text in Illustration
*a Wiper Arm Serration
*b Wiper Pivot Serration



c.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.
E250231E01
1.146,2.975 1.296,3.131 0.150,0.156 10 *1 1.488,2.827 1.31,2.975 false

Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

Text in Illustration
*1 Ceramic Dot

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E224627E01
1.928,3.503 2.678,3.503 false 2.679,3.406 2.844,3.565 0.164,0.159 10 *b 0.401,1.455 0.565,1.614 0.164,0.159 10 *a 1.282,1.543 0.583,1.543 false

When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations.

Text in Illustration
*a Wiper Arm Serration
*b Wiper Pivot Serration



b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E250230E01
1.128,2.968 1.255,3.115 0.128,0.147 10 *1 1.527,2.834 1.265,3.012 false

Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

Text in Illustration
*1 Ceramic Dot

HINT:

Hold the wiper arm by hand while tightening the nut.



d.

Turn the power switch on (IG).


e.

Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.


f.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


g.

Turn the power switch off.


Hide 85292B 8.INSTALL FRONT WIPER ARM HEAD CAP

a.
E228574

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.