Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301892 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


PROCEDURE

Hide 85292B 1.REMOVE FRONT WIPER ARM HEAD CAP

a.
E228573E05
1.458,1.427 1.698,1.594 true 1.729,1.583 1.958,1.771 0.229,0.188 10 true *1

Using a screwdriver, disengage the 3 claws and remove the front wiper arm head cap.

Text in Illustration
*1 Protective Tape

HINT:
·

Tape the screwdriver tip before use.



·

Use the same procedure for the RH side and LH side.



Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E250213

Remove the nut and front wiper arm and blade assembly LH.


Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E250214

Remove the nut and front wiper arm and blade assembly RH.


Hide 55810F 4.REMOVE FRONT VENTILATOR ASSEMBLY

a.
E228577

Disengage the 2 claws and remove the front ventilator assembly as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E250215

Remove the 2 clips.


b.

for LHD:

i.

Disengage the 5 claws and 3 guides.

E250216



c.

for RHD:

i.

Disengage the 6 claws and 3 guides.

E223391



d.

Disengage the 9 guides and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.

E250218


Hide 6.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


b.
E250220E01
1.801,0.259 1.961,0.415 0.161,0.156 10 *1 2.721,0.553 1.978,0.379 false

Disengage the 2 clamps.

Text in Illustration
*1 Grommet


c.

Remove the 2 bolts.


d.

Disengage the grommet and remove the windshield wiper motor and link assembly as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.



e.
E250221

Disconnect the connector.


Hide 85012A 7.REMOVE FRONT WIPER CRANK SUB-ASSEMBLY

a.
E250222E03
1.385,0.896 1.208,1.208 true 1.708,0.813 2.188,0.49 true 1.24,0.677 0.656,1.115 true 1.083,1.188 1.25,1.354 0.167,0.167 10 false *1 0.49,1.063 0.656,1.229 0.167,0.167 10 false *a 2.229,0.375 2.396,0.542 0.167,0.167 10 false *2

Using a screwdriver, separate the No. 1 rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.

Text in Illustration
*1 Protective Tape
*2 No. 1 Rod
*a Crank Arm Pivot

HINT:

Tape the screwdriver tip before use.



b.
E250224

Remove the nut and front wiper crank sub-assembly.


Hide 85110 8.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E250225

Remove the 2 bolt, No. 1 windshield wiper link washer and windshield wiper motor assembly.