Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter sub-assembly receives information signals from the hazard warning signal switch assembly, and blinks the turn signal lights.

WIRING DIAGRAM

E224347E04
1.115,0.656 1.979,1.115 0.865,0.458 10 false from Auxiliary battery 5.292,2.823 6.469,3.469 1.177,0.646 10 false Combination Meter Sub-assembly 2.927,1.802 3.063,1.979 0.135,0.177 10 false 3 1.042,1.802 1.177,1.979 0.135,0.177 10 false 5 1.135,2.385 3,3.073 1.865,0.688 10 false Hazard Warning Signal Switch Assembly 5.365,0.563 5.5,0.74 0.135,0.177 10 false 1 5.375,1.781 5.521,1.958 0.146,0.177 10 false 4 5.292,2.656 5.667,2.865 0.375,0.208 10 false L27 1.135,2.219 1.427,2.396 0.292,0.177 10 false L57 2.292,0.844 2.792,1.073 0.5,0.229 10 false ECU-B 5.573,0.677 6.021,0.906 0.448,0.229 10 false B 5.573,1.927 6.021,2.156 0.448,0.229 10 false HAZ 1.26,1.917 1.375,2.094 0.115,0.177 10 false E 2.708,1.917 2.823,2.094 0.115,0.177 10 false F

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard warning signal switch signal/ON or OFF ON: Hazard warning signal switch on
OFF: Hazard warning signal switch off
-

OK:

The display is as specified in the normal condition column.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.

Remove the hazard warning signal switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL).


b.
E190200E03
0.13,0.051 0.323,0.225 0.193,0.174 10 *a 2.638,1.531 2.785,1.705 0.147,0.174 10 E 0.841,1.451 0.987,1.625 0.147,0.174 10 F 1.584,1.211 0.985,1.496 false 2.038,1.391 2.604,1.6 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (F) - 5 (E) Hazard warning switch off 10 kΩ or higher
Hazard warning switch on Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH - COMBINATION METER SUB-ASSEMBLY)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L57-3 (F) - L27-4 (HAZ) Always Below 1 Ω
L57-5 (E) - Body Ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L57-3 (F) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR