Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light relay.

WIRING DIAGRAM

E248309E02
3.708,0.938 3.917,1.083 0.208,0.146 10 false 2E 3.708,3.354 3.917,3.5 0.208,0.146 10 false 26 5.958,3.438 6.167,3.583 0.208,0.146 10 false 27 5.938,1.156 6.146,1.302 0.208,0.146 10 false 14 3.74,0.75 3.833,0.896 0.094,0.146 10 false 1 3.75,1.365 3.844,1.51 0.094,0.146 10 false 1 3.708,1.146 3.948,1.292 0.24,0.146 10 false *1 3.729,1.771 3.969,1.917 0.24,0.146 10 false *2 3.708,2.906 3.917,3.052 0.208,0.146 10 false 2B 3.76,2.729 3.896,2.906 0.135,0.177 10 false 7 3.698,2.521 3.906,2.667 0.208,0.146 10 false 2A 3.719,2.323 3.938,2.469 0.219,0.146 10 false 55 2.188,3.823 2.333,3.969 0.146,0.146 10 false 5 1.146,3.823 1.292,3.969 0.146,0.146 10 false 1 2.188,5.01 2.333,5.156 0.146,0.146 10 false 5 1.146,5.01 1.292,5.156 0.146,0.146 10 false 1 1.979,2.833 2.125,2.979 0.146,0.146 10 false 2 1.354,2.823 1.5,2.969 0.146,0.146 10 false 1 1.979,2.427 2.125,2.573 0.146,0.146 10 false 5 1.354,2.438 1.469,2.583 0.115,0.146 10 false 3 0.104,0.927 0.969,1.354 0.865,0.427 10 false from Auxiliary Battery 0.896,4.156 1.229,4.302 0.333,0.146 10 false R17 0.896,4.292 2.531,4.646 1.635,0.354 10 false Rear Combination Light Assembly LH (Rear Fog) 0.885,5.385 1.146,5.531 0.26,0.146 10 false S18 0.885,5.521 2.531,5.896 1.646,0.375 10 false Rear Combination Light Assembly RH (Rear Fog) 4.938,1.531 5.313,1.677 0.375,0.146 10 false TAIL 5.385,5.531 7.042,5.865 1.656,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 3.677,4 5.333,4.385 1.656,0.385 10 false Instrument Panel Junction Block Assembly 3.708,3.542 3.917,3.688 0.208,0.146 10 false 2B 5.573,1.906 5.948,2.052 0.375,0.146 10 false TAIL 6.198,1.271 6.573,1.417 0.375,0.146 10 false TRLY 6.198,3.552 6.635,3.698 0.438,0.146 10 false RFGO 5.385,5.365 5.719,5.51 0.333,0.146 10 false MB 4.698,1.896 5.302,2.063 0.604,0.167 10 false RR FOG 1.198,3.219 1.563,3.385 0.365,0.167 10 false L153 1.604,3.219 2.969,3.385 1.365,0.167 10 false Rear Fog Light Relay 2,1.115 2.51,1.281 0.51,0.167 10 false DC/DC 2.823,6.313 3.615,6.542 0.792,0.229 10 false *1: for LHD 4.083,6.313 4.906,6.542 0.823,0.229 10 false *2: for RHD 3.708,1.552 3.917,1.698 0.208,0.146 10 false 2F 0.625,3.802 0.865,3.948 0.24,0.146 10 false *1 2.583,3.802 2.823,3.948 0.24,0.146 10 false *1 0.625,5.01 0.865,5.156 0.24,0.146 10 false *2 2.583,5.01 2.823,5.156 0.24,0.146 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch is in head position

OK:

Rear fog light relay operates. (Rear fog light comes on.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT REAR FOG LIGHT RELAY
2.INSPECT REAR FOG LIGHT RELAY
a.
B416269E04
1.729,0.719 2,0.719 false 2.656,0.719 2.927,0.719 false 2.521,1.125 2.938,1.125 false 2.531,1.625 2.948,1.625 false 1.208,1.313 1.385,1.542 0.177,0.229 10 false 1 1.219,0.76 1.396,0.99 0.177,0.229 10 false 5 0.208,0.771 0.385,1 0.177,0.229 10 false 3 0.208,1.323 0.385,1.552 0.177,0.229 10 false 2 1.604,0.646 1.781,0.875 0.177,0.229 10 false 1 2.979,0.635 3.156,0.865 0.177,0.229 10 false 2 3,1.042 3.177,1.271 0.177,0.229 10 false 5 3,1.542 3.177,1.771 0.177,0.229 10 false 3

Remove the rear fog light relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - REAR FOG LIGHT RELAY)

NG

REPLACE REAR FOG LIGHT RELAY

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - REAR FOG LIGHT RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L153-2 - Body ground Light control switch off → tail Below 1 V → 11 to 14 V
L153-5 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR COMBINATION LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR COMBINATION LIGHT ASSEMBLY)
a.

Disconnect the R17 rear combination light assembly LH connector or the S18 rear combination light assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L153-3 - R17-1 Always Below 1 Ω
L153-3 - S18-1 Always Below 1 Ω
L153-3 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the 2B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L153-1 - 2B-26 Always Below 1 Ω
2B-26 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
U191237E02
2.729,3.469 2.729,3.844 false 1.688,0.854 2.01,1.177 0.323,0.323 10 false 2B 0.135,0.094 0.333,0.25 0.198,0.156 10 false *a 1.698,2.938 2.021,3.198 0.323,0.26 10 false MB 2.531,3.885 3.094,4.104 0.563,0.219 10 false RFGO

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-26 - MB-27 (RFGO) Always Below 1 Ω
2B-26 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY