Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Speed Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly receives the vehicle speed signal from the combination meter sub-assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E251604E04
0.635,1.521 1.76,1.667 1.125,0.146 10 false Skid Control ECU 1.438,0.51 1.729,0.656 0.292,0.146 10 false SP1 0.635,1.365 0.958,1.542 0.323,0.177 10 false A58 1.792,0.51 1.979,0.656 0.188,0.146 10 false 11 3.052,7.438 4.271,7.604 1.219,0.167 10 false Junction Connector 0.563,2.969 1.896,3.344 1.333,0.375 10 false Power Management Control ECU 0.563,2.813 0.854,2.979 0.292,0.167 10 false L5 0.104,7.208 0.365,7.375 0.26,0.167 10 false A48 0.104,7.365 2.417,7.542 2.313,0.177 10 false Headlight Leveling ECU Assembly*4 1.333,6.927 1.75,7.083 0.417,0.156 10 false SPDR 1.385,2.406 1.781,2.563 0.396,0.156 10 false SPDI 1.792,2.406 1.969,2.563 0.177,0.156 10 false 14 1.792,6.917 1.979,7.073 0.188,0.156 10 false 16 3.917,2.406 4.354,2.573 0.438,0.167 10 false 31*2 3.917,2.25 4.354,2.417 0.438,0.167 10 false 32*1 2.875,2.406 3.094,2.573 0.219,0.167 10 false 22 1.792,4.24 1.99,4.406 0.198,0.167 10 false 24 5.292,6.917 5.51,7.083 0.219,0.167 10 false 11 3.917,4.24 4.302,4.406 0.385,0.167 10 false 12*2 4,4.083 4.385,4.25 0.385,0.167 10 false 3*1 2.729,4.24 3.115,4.406 0.385,0.167 10 false 21*2 2.729,4.083 3.115,4.25 0.385,0.167 10 false 12*1 3.917,6.917 4.302,7.083 0.385,0.167 10 false 11*2 3.917,6.75 4.302,6.917 0.385,0.167 10 false 21*1 2.729,6.917 3.115,7.083 0.385,0.167 10 false 32*2 2.729,6.75 3.115,6.917 0.385,0.167 10 false 31*1 5.302,0.51 5.604,0.656 0.302,0.146 10 false 16 5.302,2.406 5.573,2.552 0.271,0.146 10 false 15 5.552,0.604 5.75,0.75 0.198,0.146 10 false SI 5.552,2.51 5.75,2.656 0.198,0.146 10 false +S 4.99,2.771 5.323,2.917 0.333,0.146 10 false L27 4.99,2.927 7.104,3.313 2.115,0.385 10 false Combination Meter Sub-assembly (Meter Circuit Plate) 0.448,4.656 0.813,4.813 0.365,0.156 10 false L146 0.448,4.813 1.979,5.323 1.531,0.51 10 false Windshield Wiper Relay Assembly*3 4.979,6.021 7.052,6.313 2.073,0.292 10 false Navigation ECU Sub-assembly*6 0.563,7.917 1.375,8.094 0.813,0.177 10 false *1: for LHD 1.75,7.917 2.563,8.094 0.813,0.177 10 false *2: for RHD 2.927,7.917 4.698,8.094 1.771,0.177 10 false *3: w/ Auto Wiper System 5,7.917 6.344,8.094 1.344,0.177 10 false *4: w/ LED Headlight 0.563,8.313 2.302,8.49 1.74,0.177 10 false *5: w/o Navigation System 2.927,8.313 4.531,8.49 1.604,0.177 10 false *6: w/ Navigation System 1.448,4.24 1.771,4.385 0.323,0.146 10 false SPD 5.542,6.917 5.865,7.063 0.323,0.146 10 false SPD 4.979,5.865 5.25,6.01 0.271,0.146 10 false L38 4.49,7.219 4.76,7.375 0.271,0.156 10 false L31 4.552,4.51 4.854,4.667 0.302,0.156 10 false L35 4.49,7.375 7.125,7.552 2.635,0.177 10 false Stereo Component Amplifier Assembly*7 4.552,4.667 7.083,4.844 2.531,0.177 10 false Radio and Display Receiver Assembly*5 2.76,7.438 3.073,7.604 0.313,0.167 10 false L70 5.552,4.24 5.865,4.406 0.313,0.167 10 false SPD 5.313,4.24 5.49,4.406 0.177,0.167 10 false 17 5.552,5.583 5.865,5.75 0.313,0.167 10 false SPD 5.313,5.583 5.49,5.75 0.177,0.167 10 false 17 5,8.313 6.708,8.49 1.708,0.177 10 false *7: for 8 Speakers

PROCEDURE

1.CHECK METER / GAUGE SYSTEM
a.

The circuits that send vehicle speed signals to this system are inspected in the meter section (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit).


b.

During inspection for the meter/gauge system, if there is an instruction that indicates to go back to inspections for the lighting system, proceed to the next step.



NEXT

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the A48 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-16 (SPDR) - L27-15 (+S) Always Below 1 Ω




OK

3.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)
a.
E343932E03
1.5,0.417 1.917,0.667 0.417,0.25 1.24,1.177 1,0.729 false 0.146,0.104 0.365,0.313 0.219,0.208 10 false *a 0.813,0.573 1.021,0.771 0.208,0.198 10 false S+ 1.042,4.021 1.375,4.25 0.333,0.229 10 false (A) 2.875,3.688 3.219,3.875 0.344,0.188 10 false GND 1.583,0.458 1.927,0.646 0.344,0.188 10 false L27

Check the output waveform.

i.

Remove the combination meter sub-assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approximately 20 km/h (12 mph)

OK:

The waveform is displayed as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Sub-assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG