Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E220287E05
1.604,2.396 2.656,2.573 1.052,0.177 10 false Taillight RH 1.448,1.698 2.521,1.875 1.073,0.177 10 false Parking Lights 0.125,3.073 2.49,3.396 2.365,0.323 10 false Taillight LH and License Plate Lights 3.365,1.51 3.656,1.75 0.292,0.24 10 false 10 3.365,2.385 3.583,2.563 0.219,0.177 10 false 2B 3.365,1.708 3.583,1.885 0.219,0.177 10 false 2C 3.365,3.073 3.563,3.25 0.198,0.177 10 false 2D 3.344,2.865 3.542,3.052 0.198,0.188 10 false 18 3.396,2.177 3.49,2.354 0.094,0.177 10 false 7 0.313,0.417 1.188,0.771 0.875,0.354 10 false from Auxiliary Battery 2.052,0.656 2.594,0.906 0.542,0.25 10 false DC/DC 3.365,0.479 3.573,0.656 0.208,0.177 10 false 2E 3.406,0.292 3.5,0.469 0.094,0.177 10 false 1 4.594,1.146 4.906,1.323 0.313,0.177 10 false TAIL 5.323,1.031 5.635,1.208 0.313,0.177 10 false TAIL 6.365,0.479 6.781,0.656 0.417,0.177 10 false TRLY 6.115,0.375 6.292,0.552 0.177,0.177 10 false 14 5.427,3.917 7.052,4.323 1.625,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.427,3.76 5.76,3.948 0.333,0.188 10 false MB 3.333,3.5 4.958,3.906 1.625,0.406 10 false Instrument Panel Junction Block Assembly 3.375,0.677 3.542,0.823 0.167,0.146 10 false *1 3.375,1.083 3.583,1.26 0.208,0.177 10 false 2F 3.406,0.885 3.5,1.063 0.094,0.177 10 false 1 3.375,1.281 3.542,1.427 0.167,0.146 10 false *2 0.906,4.26 1.677,4.417 0.771,0.156 10 false *1: for LHD 1.958,4.26 2.729,4.417 0.771,0.156 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -

OK:

Taillight relay operates. (Taillights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U191269E01
0.89,0.604 1.079,0.760 0.189,0.156 10 2F 1.198,0.604 1.387,0.760 0.189,0.156 10 *B 0.89,0.324 1.079,0.480 0.189,0.156 10 2E 1.198,0.324 1.387,0.480 0.189,0.156 10 *A 2.934,0.604 3.129,0.760 0.195,0.156 10 2C 5.707,0.604 5.905,0.760 0.198,0.156 10 2D 1.424,2.207 1.613,2.363 0.189,0.156 10 2B 4.93,2.399 5.156,2.555 0.226,0.156 10 MB 4.754,2.951 4.515,3.322 false 4.328,3.346 4.701,3.502 0.373,0.156 10 TRLY 0.147,0.127 0.375,0.298 0.228,0.171 10 *a

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Connect a positive (+) lead from the auxiliary battery to terminal 2E-1*1 or 2F-1*2.


c.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2C-10 - Auxiliary battery negative terminal Always 11 to 14 V
2D-18 - Auxiliary battery negative terminal Always 11 to 14 V
2B-7 - Auxiliary battery negative terminal Always 11 to 14 V


*1: for LHD

*2: for RHD




OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2E*1 or 2F*2 instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2E-1*1 - Body ground Power switch off 11 to 14 V
2F-1*2 - Body ground Power switch off 11 to 14 V


*1: for LHD

*2: for RHD




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR