Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.11–2017.12
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  FAIL-SAFE CHART  


HEADLIGHT (for LED HEADLIGHT)


The light control ECU operates in fail-safe mode if an abnormal condition such as those listed below has been detected.

Item Fail-safe operation
Open in output side circuit
·

Stops illuminating the headlights

·

Keeps the headlights off until the power is reinstated (by turning the light control switch from off to the head position).


Short between output terminal and body ground
·

Stops illuminating the headlights

·

Keeps the headlights off until the power is reinstated (by turning the light control switch from off to the head position).


Abnormal power source voltage (17 to 23 V) is detected.
·

Stops illuminating the headlights when the input voltage becomes too high (17 to 23 V).

·

Illuminates the headlights again when the voltage returns to the operating voltage range (10 to 16 V).


Abnormal power source voltage (7 to 10 V) is detected.
·

Limits the LED output current when the power source voltage is 7 to 10 V. (Headlights remain illuminated.)

·

Illuminates the headlights again when the voltage returns to the operating voltage range (10 to 16 V).


Abnormal power source voltage (5.1 to 7 V) is detected.
·

Stops illuminating the headlights when the input voltage becomes too low (5.1 to 7 V).

·

Illuminates the headlights again when the voltage returns to the operating voltage range (9.2 V or more).




AUTOMATIC LIGHT CONTROL SYSTEM


If the main body ECU (multiplex network body ECU) detects a malfunction in the automatic light control sensor, the main body ECU (multiplex network body ECU) performs fail-safe control to prohibit the automatic light control. If the low beam headlights and taillights are on, the lights will remain on until the light control switch is turned off.


AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM


a.

The headlight leveling ECU assembly operates in fail-safe mode if an abnormal condition such as those listed below has been detected, and keep the last low beam status.

Item Abnormality Detection Condition Return Condition Warning Indicator
Height control sensor power source voltage Abnormal height control sensor power source voltage (4.6 V or less, or 6.25 V or more) is detected. Abnormal voltage is not detected for 5 seconds consecutively Illuminated
Height control sensor signal voltage Abnormal height control sensor signal voltage (0.25 V or less, or 4.75 V or more) is detected.
High power source voltage Abnormal high IG supply voltage (18.5 V or more) is detected. Voltage of 17.5 V or less is detected Not illuminated
Low power source voltage Abnormal low IG supply voltage (9.0 V or less) is detected. Voltage of 9.3 V or more is detected for 0.1 seconds consecutively Not illuminated
Height control sensor data out of range Height control sensor data out of range when performing initialization of the headlight leveling ECU assembly Vehicle condition is proper for initialization. Illuminated
Variation error Headlight leveling ECU assembly for another destination is installed on the vehicle Headlight leveling ECU assembly for proper destination is installed on the vehicle Illuminated



AUTOMATIC HIGH BEAM SYSTEM


a.

The main body ECU (multiplex network body ECU) operates in fail-safe mode if an abnormal condition such as those listed below has been detected.

Item Abnormality Detection Condition Return Condition Warning (Multi-information Display)
Yaw Rate Signal Malfunction Normal yaw rate signal is not detected. Normal yaw rate signal is detected. "HEAD LIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed
Speed Sensor Signal Malfunction Normal speed sensor signal is not detected. Normal speed sensor signal is detected. "HEAD LIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed
CAN Communication System Malfunction Normal CAN communication system is not detected. Normal CAN communication system is detected. "HEAD LIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed
Lane Departure Warning Camera Signal Malfunction Normal lane departure warning camera signal is not detected. Normal lane departure warning camera signal is detected. "HEAD LIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" message is displayed