These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU (multiplex network body ECU).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2430 | LED headlight LH circuit malfunction | ·
Light control ECU LH ·
Headlight unit LH ·
No. 1 integration relay ·
Harness or connector ·
Main body ECU (multiplex network body ECU) |
| B2431 | LED headlight RH circuit malfunction | ·
Light control ECU RH ·
Headlight unit RH ·
No. 1 integration relay ·
Harness or connector ·
Main body ECU (multiplex network body ECU) |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Clear the DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Both DTC B2430 and B2431 are not output. | A |
| Both DTC B2430 and B2431 are output. | B |
| DTC B2430 or B2431 is output. | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Disconnect the 1H No. 1 integration relay connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
|---|---|---|
| 1H-7 (BATT) - Body ground | Power switch off | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1H-3 (GND2) - Body ground | Always | Below 1 Ω |
Disconnect the 1G integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1G-22 (GND1) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the 2C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1G-9 (HL4) - 2C-32 | Always | Below 1 Ω |
| 1G-9 (HL4) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2C-32 - MB-15 (HRLY) | Always | Below 1 Ω |
| 2C-32 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG
Replace the No. 1 integration relay with a new or known good one (See page Power Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2430 and B2431 are not output.
OK
NG
Disconnect the A10 headlight assembly LH connector or the A39 headlight assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-3 (LO) - Body ground | Light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-3 (LO) - Body ground | Light control switch in head position | 11 to 14 V |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-2 (PPOS) - Body ground | Power switch on (IG) and light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-2 (PPOS) - Body ground | Power switch on (IG) and light control switch in head position | 11 to 14 V |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-1 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Replace the light control ECU with a new or known good one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2430 or B2431 is not output.
OK
NG
Disconnect the 1G No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1G-2 (HLPL) - A10-3 (LO) | Always | Below 1 Ω |
| 1G-2 (HLPL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1G-1 (HLPR) - A39-3 (LO) | Always | Below 1 Ω |
| 1G-1 (HLPR) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the L8 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L8-21 (LLEW) - A10-2 (PPOS) | Always | Below 1 Ω |
| L8-21 (LLEW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L8-5 (RLEW) - A39-2 (PPOS) | Always | Below 1 Ω |
| L8-5 (RLEW) - Body ground | Always | 10 kΩ or higher |
OK
NG