Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the headlight relays located within the No. 1 integration relay.

WIRING DIAGRAM

E241387E06
5.5,8.031 7.146,8.417 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.427,2.094 2.948,2.292 1.521,0.198 10 false No.1 Integration Relay 1.49,5.948 3.125,6.156 1.635,0.208 10 false Headlight Assembly RH*1 2.865,0.729 3.063,0.875 0.198,0.146 10 false 9 2.802,0.948 3.063,1.094 0.26,0.146 10 false 1G 2.792,1.813 3.052,1.958 0.26,0.146 10 false 1G 1.26,1.385 1.521,1.531 0.26,0.146 10 false 1G 2.802,1.375 3.063,1.521 0.26,0.146 10 false 1G 1.271,1.802 1.479,1.948 0.208,0.146 10 false 1H 4.729,0.75 4.938,0.896 0.208,0.146 10 false 32 4.719,0.938 4.927,1.094 0.208,0.156 10 false 2C 1.292,1.177 1.5,1.323 0.208,0.146 10 false 22 2.281,1.813 2.646,1.958 0.365,0.146 10 false HLPL 1.604,1.813 2.021,1.958 0.417,0.146 10 false GND2 1.615,1.396 2.031,1.542 0.417,0.146 10 false GND1 2.25,1.385 2.646,1.531 0.396,0.146 10 false HLPR 2.854,1.594 2.958,1.74 0.104,0.146 10 false 2 1.333,1.604 1.438,1.75 0.104,0.146 10 false 3 2.844,1.177 2.948,1.323 0.104,0.146 10 false 1 1.271,0.958 1.531,1.104 0.26,0.146 10 false 1H 1.333,0.75 1.438,0.896 0.104,0.146 10 false 7 1.99,0.469 2.427,0.677 0.438,0.208 10 false P/I 2 3.01,0.313 4.375,0.49 1.365,0.177 10 false from Auxiliary Battery 6.281,0.948 6.708,1.219 0.427,0.271 10 false HRLY 5.958,0.75 6.167,0.896 0.208,0.146 10 false 15 4.594,1.281 6.24,1.781 1.646,0.5 10 false Instrument Panel Junction Block Assembly 1.458,2.583 1.552,2.729 0.094,0.146 10 false 1 1.792,3.573 2.469,3.729 0.677,0.156 10 false Low (LED) 1.125,5.948 1.448,6.104 0.323,0.156 10 false A42 1.354,2.969 3.052,3.177 1.698,0.208 10 false Headlight Assembly LH*1 1.021,2.969 1.333,3.125 0.313,0.156 10 false A13 1.354,5.073 3.052,5.281 1.698,0.208 10 false Headlight Assembly LH*2 1.021,5.073 1.333,5.229 0.313,0.156 10 false A84 2.729,2.583 2.823,2.729 0.094,0.146 10 false 2 1.448,5.563 1.542,5.708 0.094,0.146 10 false 1 1.802,6.542 2.49,6.698 0.688,0.156 10 false Low (LED) 2.719,5.563 2.813,5.708 0.094,0.146 10 false 2 5.938,0.948 6.167,1.094 0.229,0.146 10 false MB 1.615,0.958 2.021,1.115 0.406,0.156 10 false BATT 2.375,0.938 2.646,1.094 0.271,0.156 10 false HL4 1.625,2.594 1.771,2.74 0.146,0.146 10 false E 1.615,5.563 1.76,5.708 0.146,0.146 10 false E 2.479,5.573 2.792,5.792 0.313,0.219 10 false LO 2.469,2.604 2.729,2.75 0.26,0.146 10 false LO 3.656,4.344 3.75,4.49 0.094,0.146 10 false 3 3.396,4.344 3.656,4.49 0.26,0.146 10 false LO 3.656,7.333 3.75,7.479 0.094,0.146 10 false 3 3.385,7.333 3.646,7.479 0.26,0.146 10 false LO 0.542,4.344 0.635,4.49 0.094,0.146 10 false 6 0.708,4.344 0.854,4.49 0.146,0.146 10 false E 0.531,7.313 0.625,7.458 0.094,0.146 10 false 6 0.698,7.313 0.844,7.458 0.146,0.146 10 false E 1.396,8.063 3.031,8.271 1.635,0.208 10 false Headlight Assembly RH*2 1.031,8.063 1.354,8.219 0.323,0.156 10 false A86 1.563,4.177 2.708,4.385 1.146,0.208 10 false Light Control ECU 1.552,7.167 2.698,7.375 1.146,0.208 10 false Light Control ECU 0.573,8.417 2.156,8.625 1.583,0.208 10 false *1: for Halogen Headlight 2.969,8.417 4.552,8.625 1.583,0.208 10 false *2: for LED Headlight

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relays operate.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Headlight relays ON/OFF -

OK:

Headlight relays operate. (Low beam headlights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - AUXILIARY BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the 1H No. 1 integration relay connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connector Condition Specified Condition
1H-7 (BATT) - Body ground Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
1H-3 (GND2) - Body ground Always Below 1 Ω



c.

Disconnect the 1G No. 1 integration relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-22 (GND1) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-9 (HL4) - 2C-32 Always Below 1 Ω
1G-9 (HL4) - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
U155048E02
0.164,0.16 0.364,0.347 0.200,0.187 10 *a 1.62,0.824 1.858,1.005 0.238,0.181 10 2C 1.614,2.99 1.964,3.171 0.350,0.181 10 MB 1.376,3.762 1.789,3.913 0.413,0.151 10 HRLY 1.594,3.486 1.594,3.748 false

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-32 - MB-15 (HRLY) Always Below 1 Ω
2C-32 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

5.CHECK NO. 1 INTEGRATION RELAY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK NO. 1 INTEGRATION RELAY
a.

Replace the No. 1 integration relay with a new or known good one (See page Power Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL).


b.

Check that the low beam headlights operate normally.

OK:

Low beam headlights operate normally.




OK

END (NO. 1 INTEGRATION RELAY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)