Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › from 2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301909 HEADLIGHT ASSEMBLY N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment procedure.


PROCEDURE

Hide 1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure that there is no damage or deformation to the vehicle body around the headlights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the engine coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Sit a person of average weight (75 kg, 165 lb) in the driver's seat.

·
E107873

Vehicles with the manual headlight beam level control system should be set to "0".



Hide 2. PREPARE FOR HEADLIGHT AIMING (Using a screen)

a.
E228265E02
0.834,1.721 1.729,1.887 0.895,0.166 10 25 m or 3 m

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (headlight bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of headlight aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




b.

Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E228266E03
0.719,0.125 2.948,0.333 2.229,0.208 12 false Alignment distance is 25 m: 4.177,0.125 6.177,0.333 2,0.208 12 false Alignment distance is 3 m: 4.427,1.552 5.115,1.729 0.688,0.177 10 false V LH Line 4.417,0.656 5.104,0.833 0.688,0.177 10 false V RH Line 6.521,1.115 6.969,1.271 0.448,0.156 10 false V Line 0.979,1.542 1.667,1.719 0.688,0.177 10 false V LH Line 1,0.667 1.688,0.844 0.688,0.177 10 false V RH Line 3.083,1.115 3.531,1.271 0.448,0.156 10 false V Line 0.146,2.823 0.708,3.042 0.563,0.219 10 false H Line 3.573,2.833 4.115,3.042 0.542,0.208 10 false H Line 1.281,3.469 1.75,3.781 0.469,0.313 10 false 25 m 4.75,3.438 5.01,3.75 0.26,0.313 10 false 3 m 1.135,2.99 1.458,3.292 0.323,0.302 10 false 90° 1.125,0.958 1.448,1.26 0.323,0.302 10 false 90° 4.583,0.948 4.906,1.25 0.323,0.302 10 false 90° 4.563,2.99 4.885,3.292 0.323,0.302 10 false 90°

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423E79
0.969,0.188 1.156,0.344 0.188,0.156 10 false *a 1.615,0.188 1.792,0.344 0.177,0.156 10 false *b 0.365,1.729 0.542,1.885 0.177,0.156 10 false *e 2.74,0.854 2.927,1.021 0.188,0.167 10 false *d 2.25,0.188 2.438,0.344 0.188,0.156 10 false *c

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground

HINT:
·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb.



i.

H Line (Headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



Hide 3.INSPECT HEADLIGHT AIMING

a.

Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam, cover the low beam or disconnect the connector.



b.

Start the engine.


c.

Turn on the headlights and check if the cutoff line for each low beam matches the preferred cutoff line in the illustration.

E234067E28
1.99,1.854 2.281,0.75 2.281,0.75 2.5,0.75 true 1.25,2.177 1.417,2.177 1.417,2.177 1.51,1.875 false 4.677,2.188 4.844,2.188 4.844,2.188 4.938,1.885 false 5.5,1.833 5.781,0.969 5.781,0.969 6,0.969 true 0.927,0.156 3.208,0.448 2.281,0.292 12 false Alignment distance is 25 m: 4.281,0.146 6.24,0.417 1.958,0.271 12 false Alignment distance is 3 m: 2.542,0.677 3.125,0.865 0.583,0.188 10 false Point A 1.281,0.698 1.958,0.875 0.677,0.177 10 false V LH Line 1.281,0.969 2,1.146 0.719,0.177 10 false V RH Line 1.333,1.25 1.906,1.417 0.573,0.167 10 false 48 mm 0.135,1.479 0.677,1.656 0.542,0.177 10 false H Line 0.26,1.76 0.885,1.938 0.625,0.177 10 false 249 mm 0.552,2.104 1.229,2.646 0.677,0.542 10 false Preferred Cutoff Line 3.115,1.688 3.729,1.865 0.615,0.177 10 false 698 mm 1.448,2.25 2.073,2.438 0.625,0.188 10 false 248 mm 2.042,2.26 2.667,2.448 0.625,0.188 10 false 248 mm 6.604,1.708 7.156,1.885 0.552,0.177 10 false 83 mm 4.823,1.24 5.271,1.417 0.448,0.177 10 false 6 mm 3.833,1.771 4.385,1.948 0.552,0.177 10 false 30 mm 4.99,2.26 5.542,2.438 0.552,0.177 10 false 29 mm 5.51,2.26 6.063,2.438 0.552,0.177 10 false 29 mm 4,2.115 4.667,2.604 0.667,0.49 10 false Preferred Cutoff Line 6.063,0.896 6.656,1.073 0.594,0.177 10 false Point A 3.625,1.49 4.167,1.667 0.542,0.177 10 false H Line 4.781,0.729 5.458,0.906 0.677,0.177 10 false V LH Line 4.781,0.969 5.5,1.146 0.719,0.177 10 false V RH Line 0.573,2.875 4.073,3.438 3.5,0.563 10 false The illustration shown is for an LHD vehicle. RHD vehicles will project a headlight pattern that is a mirror image.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82 ft.):

The low beam cutoff line should be between 48 mm (1.89 in.) and 698 mm (2.29 ft.) below the H line as well as 248 mm (9.79 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be between 6 mm (0.227 in.) and 83 mm (3.29 in.) below the H line as well as 29 mm (1.17 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 25 m (82 ft.):

The horizontal line of the preferred low beam cutoff line is 249 mm (9.79 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.




d.

Turn on the high beams and check if the center of intensity for each high beam matches the preferred center of the intensity in the illustration.

E235330E46
1.99,1.594 2.26,0.583 2.26,0.583 2.406,0.583 true 5.479,1.583 5.76,0.573 5.76,0.573 5.896,0.573 true 0.708,0.031 2.771,0.396 2.063,0.365 12 false Alignment distance is 25 m: 4.208,0.031 6.271,0.396 2.063,0.365 12 false Alignment distance is 3 m: 1.302,0.708 1.958,1.021 0.656,0.313 10 false V LH Line 0.521,1.51 0.948,1.813 0.427,0.302 10 false H Line 5.667,2.188 6.125,2.5 0.458,0.313 10 false 59 mm 4.865,2.188 5.323,2.5 0.458,0.313 10 false 59 mm 2.125,2.188 2.667,2.5 0.542,0.313 10 false 497 mm 1.344,2.188 1.885,2.5 0.542,0.313 10 false 497 mm 4.01,1.521 4.438,1.823 0.427,0.302 10 false H Line 6.635,1.865 7.115,2.177 0.479,0.313 10 false 29 mm 6.635,1.323 7.115,1.635 0.479,0.313 10 false 20 mm 3.135,1.875 3.688,2.188 0.552,0.313 10 false 248 mm 3.135,1.354 3.677,1.667 0.542,0.313 10 false 174 mm 2.448,0.5 3.073,1.146 0.625,0.646 10 false Center of Intensity 5.948,0.49 6.594,1.135 0.646,0.646 10 false Center of Intensity 1.302,1 1.958,1.365 0.656,0.365 10 false V RH Line 4.802,0.698 5.458,1.01 0.656,0.313 10 false V LH Line 4.802,1 5.458,1.365 0.656,0.365 10 false V RH Line

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82 ft.): The high beam center of intensity should be within 174 mm (6.87 in.) above and 248 mm (9.79 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.): The high beam center of intensity should be within 20 mm (0.824 in.) above and 29 mm (1.17 in.) below the H line as well as 59 mm (2.35 in.) left or right of the V LH or V RH line.




Hide 4.ADJUST HEADLIGHT AIMING

a.

Adjust the aim vertically:

E307259E02
5.333,1.99 5.344,2.521 true 1.552,1.885 1.563,2.521 true 5.271,2.531 5.552,2.76 0.281,0.229 10 true *a 1.49,2.531 1.74,2.708 0.25,0.177 10 true *a 3.646,0.063 3.938,0.385 0.292,0.323 12 false *B 0.073,0.063 0.365,0.385 0.292,0.323 12 false *A

Text in Illustration
*A for Halogen Headlight *B for LED Headlight
*a Aiming Screw (A) - -

Adjust the aim of each headlight to the specified range by turning each aiming screw (A) with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves down when turning the aiming screw clockwise, and moves up when turning the aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.




b.

Adjust the aim horizontally:

E307258E02
4.625,1.271 4.625,2.396 false 0.938,1.125 0.938,2.375 false 4.542,2.375 4.938,2.667 0.396,0.292 10 true *a 0.865,2.365 1.094,2.583 0.229,0.219 10 true *a 3.646,0.083 4.25,0.406 0.604,0.323 12 false *B 0.073,0.083 0.927,0.417 0.854,0.333 12 false *A

Text in Illustration
*A for Halogen Headlight *B for LED Headlight
*a Aiming Screw (B) - -

Adjust the aim of each headlight to the specified range by turning each aiming screw (B) with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If it is not possible to correctly adjust headlight aim, check bulb, headlight unit and headlight unit reflector installation.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.