Home › Vehicle Exterior › LIGHTING (EXT) › FOG LIGHT ASSEMBLY
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301910 FOG LIGHT ASSEMBLY N

LIGHTING (EXT)  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

It is possible that a bulb is incorrectly installed, affecting fog light aim. Bulb installation should be considered prior to performing the adjustment procedure.


PROCEDURE

Hide 1. PREPARE VEHICLE FOR FOG LIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure there is no damage or deformation to the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Sit a person of average weight (75 kg, 165 lb) in the driver's seat.



Hide 2. PREPARE FOR FOG LIGHT AIMING

a.
E228274E02
0.808,1.719 1.709,1.879 0.901,0.160 10 25 m or 3 m

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (fog light bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




b.

Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E228275E05
1.01,2.771 1.333,3.073 0.323,0.302 10 false 90° 4.458,2.75 4.781,3.052 0.323,0.302 10 false 90° 0.74,0.135 2.969,0.344 2.229,0.208 12 false Alignment distance is 25 m: 4.167,0.135 6.167,0.344 2,0.208 12 false Alignment distance is 3 m: 4.417,1.5 5.104,1.677 0.688,0.177 10 false V LH Line 4.438,0.656 5.125,0.833 0.688,0.177 10 false V RH Line 6.521,1.146 6.969,1.302 0.448,0.156 10 false V Line 1,1.51 1.688,1.688 0.688,0.177 10 false V LH Line 0.948,0.615 1.635,0.792 0.688,0.177 10 false V RH Line 3.094,1.146 3.542,1.302 0.448,0.156 10 false V Line 0.156,3.031 0.625,3.24 0.469,0.208 10 false H Line 3.573,3.031 4.01,3.177 0.438,0.146 10 false H Line 1.26,3.438 1.729,3.75 0.469,0.313 10 false 25 m 4.74,3.438 5,3.75 0.26,0.313 10 false 3 m 1.125,0.969 1.448,1.271 0.323,0.302 10 false 90° 4.563,0.969 4.885,1.271 0.323,0.302 10 false 90°

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423E79
0.969,0.188 1.156,0.344 0.188,0.156 10 false *a 1.615,0.188 1.792,0.344 0.177,0.156 10 false *b 0.365,1.729 0.542,1.885 0.177,0.156 10 false *e 2.74,0.854 2.927,1.021 0.188,0.167 10 false *d 2.25,0.188 2.438,0.344 0.188,0.156 10 false *c

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground

HINT:

Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb.


i.

H Line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the fog light bulbs).



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.


b.

Start the engine.


c.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

E363938E01
5.646,2.313 5.396,2.313 5.396,2.313 5.313,1.885 true 2.26,2.281 2.01,2.281 2.01,2.281 1.927,1.854 true 1.031,0.156 2.833,0.365 1.802,0.208 10 false Alignment distance is 25 m: 4.438,0.167 6.24,0.375 1.802,0.208 10 false Alignment distance is 3 m: 1.531,0.625 2.313,0.865 0.781,0.24 10 false V LH Line 1.531,1 2.313,1.24 0.781,0.24 10 false V RH Line 4.854,0.635 5.635,0.875 0.781,0.24 10 false V LH Line 4.844,1 5.625,1.24 0.781,0.24 10 false V RH Line 3.625,1.469 4.167,1.677 0.542,0.208 10 false H Line 6.104,1.917 6.646,2.125 0.542,0.208 10 false 46 mm 5.708,2.24 6.417,2.5 0.708,0.26 10 false Hot Zone 2.719,1.906 3.26,2.115 0.542,0.208 10 false 376 mm 2.313,2.208 3.021,2.469 0.708,0.26 10 false Hot Zone 0.271,1.458 0.813,1.667 0.542,0.208 10 false H Line

HINT:
·

If the alignment distance is 25 m (82 ft.):

The upper edge of the hot zone for the fog light should be 376 mm (1.24 ft.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 46 mm (1.78 in.) below the H line.




Hide 4.ADJUST FOG LIGHT AIMING

a.
E222922E01
2.296,2.906 2.449,3.064 0.152,0.158 10 *1 2.031,2.996 2.284,2.996 false

Adjust the aim vertically:

Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.

Text in Illustration
*1 Aiming Screw

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:

If it is not possible to correctly adjust fog light aim, check bulb, fog light unit and fog light unit reflector installation.