Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH › 2014.11–2020.08
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301917 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY (w/ Dynamic Radar Cruise Control System)

a.
U191363E01
1.531,0.291 1.902,0.446 0.372,0.156 10 A79 0.18,0.156 0.333,0.312 0.152,0.156 10 *a 0.988,1.72 1.317,1.876 0.329,0.156 10 GND 1.351,1.19 1.179,1.699 false 1.97,1.72 2.085,1.876 0.115,0.156 10 B 2.021,1.179 2.019,1.71 false 2.374,1.72 2.489,1.876 0.115,0.156 10 B 2.221,1.178 2.415,1.72 false

Disconnect the A79 stop light switch assembly connector.


b.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A79-7 (B) - A79-2 (GND) Power switch off 11 to 14 V
A79-6 (B) - A79-2 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)

If the result is not as specified, replace the stop light switch assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A79-2 (GND) - Body ground Always Below 1 Ω



d.
U191361E01
1.539,0.411 1.969,0.567 0.430,0.156 10 A79 0.18,0.156 0.337,0.312 0.157,0.156 10 *a 0.713,1.72 1.049,1.876 0.336,0.156 10 ACC 1.689,1.127 0.942,1.703 false 2.344,1.72 2.672,1.876 0.328,0.156 10 GND 1.916,1.127 2.508,1.703 false 2.928,1.72 3.256,1.876 0.328,0.156 10 OUT 2.071,1.127 3.041,1.703 false 2.034,1.72 2.133,1.876 0.099,0.156 10 L 1.813,1.127 2.061,1.703 false 1.57,1.123 0.511,1.72 false 0.442,1.72 0.540,1.876 0.099,0.156 10 L

Reconnect the A79 stop light switch assembly connector.


e.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A79-1 (OUT) - A79-2 (GND) Power switch off, brake pedal not depressed Below 1 V
A79-1 (OUT) - A79-2 (GND) Power switch off, brake pedal depressed 11 to 14 V
A79-3 (L) - A79-2 (GND) Power switch off, brake pedal not depressed Below 1 V
A79-4 (ACC) - A79-2 (GND) Power switch off 11 to 14 V
A79-3 (L) - A79-2 (GND) Power switch off, brake pedal depressed 11 to 14 V
A79-5 (L) - A79-2 (GND) Power switch on (IG), brake pedal not depressed 11 to 14 V
A79-5 (L) - A79-2 (GND) Power switch on (IG), brake pedal depressed Below 1 V


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)

If the result is not as specified, replace the stop light switch assembly.


Hide 84340 2.INSPECT STOP LIGHT SWITCH ASSEMBLY (w/o Dynamic Radar Cruise Control System)

a.
U191359E02
1.406,1.417 1.052,1.635 false 1.719,1.438 1.719,1.792 false 2.052,1.406 2.375,1.615 false 0.219,0.135 0.448,0.313 0.229,0.177 10 false *a 1.594,0.5 2.021,0.677 0.427,0.177 10 false A80 0.917,1.594 1.042,1.771 0.125,0.177 10 false B 1.552,1.813 1.917,1.99 0.365,0.177 10 false GND 2.396,1.594 2.604,1.771 0.208,0.177 10 false B

Disconnect the A80 stop light switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-1 (B) - A80-3 (GND) Power switch off 11 to 14 V
A80-5 (B) - A80-3 (GND) Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A80-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)

If the result is not as specified, repair or replace the wire harness or connector.


c.
U191360E02
1.708,1.125 1.417,1.698 false 1.885,1.125 2.354,1.688 false 1.531,1.125 0.958,1.688 false 0.188,0.135 0.417,0.313 0.229,0.177 10 false *a 1.583,0.271 2,0.469 0.417,0.198 10 false A80 1.208,1.729 1.573,1.906 0.365,0.177 10 false GND 2.281,1.708 2.729,1.906 0.448,0.198 10 false OUT 0.865,1.698 1,1.875 0.135,0.177 10 false L

Reconnect the A80 stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-2 (OUT) - A80-3 (GND) Power switch off, brake pedal not depressed Below 1 V
A80-2 (OUT) - A80-3 (GND) Power switch off, brake pedal depressed 11 to 14 V
A80-4 (L) - A80-3 (GND) Power switch on (IG), brake pedal not depressed 11 to 14 V
A80-4 (L) - A80-3 (GND) Power switch on (IG), brake pedal depressed Below 1 V


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)

If the result is not as specified, replace the stop light switch assembly.