Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM2070E _59 Vehicle Exterior _061955 EXTERIOR PANELS / TRIM _0301939 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Perform the following procedure only if the windshield outside sub moulding will be replaced with a new one without removing the windshield glass.


PROCEDURE

Hide 1.CLEAN WINDSHIELD GLASS

a.

Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



b.

Clean the windshield outside sub moulding installation surfaces of the windshield glass with a non-residue solvent.

NOTICE:

Do not touch the windshield glass surface after cleaning it.



Hide 75549A 2.INSTALL WINDSHIELD OUTSIDE SUB MOULDING

a.

Using a brush or a sponge, coat the application area of a new windshield outside sub moulding with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.

Apply adhesive to the windshield outside sub moulding.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B277802E01
1.02,1.39 1.156,1.597 0.136,0.207 10 a 1.373,0.653 1.535,0.860 0.161,0.207 10 *1 1.349,0.747 1.145,0.747 false

Cut off the tip of the cartridge nozzle as shown in the illustration.

Text in Illustration
*1 Cartridge Nozzle

Standard Dimension:
Area Dimension
a 3.0 mm (0.118 in.)


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield outside sub moulding as shown in the illustration.

B278014E02
1.74,0.792 1.563,0.792 false 3.052,0.875 3.219,1.146 false 5.542,0.802 5.365,0.802 false 1.229,0.469 1.375,0.719 0.146,0.25 10 false b 1.771,0.698 1.917,0.948 0.146,0.25 10 false *b 3.104,1.333 3.25,1.583 0.146,0.25 10 false a 2.917,0.698 3.063,0.948 0.146,0.25 10 false *a 5.823,0.469 5.969,0.719 0.146,0.25 10 false b 5.198,0.708 5.344,0.958 0.146,0.25 10 false *b

Text in Illustration
*a Adhesive application location *b Adhesive application limit

Standard Dimension:
Area Dimension
a 3.0 mm (0.118 in.)
b 13.0 mm (0.512 in.)


HINT:

The adhesive will be easier to apply if the windshield outside sub moulding is secured to a workbench.




c.
B277803E03
2.938,0.26 3.104,0.521 0.167,0.26 10 false a 0.417,0.25 0.583,0.51 0.167,0.26 10 false a 1.302,1.75 1.469,2.01 0.167,0.26 10 false A 1.302,2.281 1.469,2.542 0.167,0.26 10 false A 0.865,3.552 1.156,3.75 0.292,0.198 10 false A-A

Install the windshield outside sub moulding onto the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.5 to 3.5 mm (0.0591 to 0.137 in.)


NOTICE:
·

Center the windshield outside sub moulding so that the distance from each end to the edges of windshield glass is equal.

·

Make sure that the whole windshield outside sub molding is firmly secured.




d.
B277682E01
0.7,1.721 1.017,2.038 0.317,0.317 10 (1) 1.254,1.585 1.571,1.902 0.317,0.317 10 (2) 1.328,2.645 1.511,2.810 0.183,0.165 10 *a 1.295,2.741 1.118,2.564 false

Press on the windshield outside sub moulding installation surfaces in the order shown in the illustration.

Text in Illustration
*a Remaining portion of old windshield outside sub moulding

HINT:

Remove any excessive adhesive that seeps out before it hardens.



e.

Hold the windshield outside sub moulding using protective tape until the adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Usage Time Frame
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



f.

After confirming that the adhesive has hardened, remove the tape.