Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.08–2016.05
RM2070E _59 Vehicle Exterior _061962 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0301952 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible  


DESCRIPTION

The vehicle approaching speaker controller communicates with the GTS through the DLC3.

WIRING DIAGRAM

E282281E12
0.177,1.542 3.094,1.771 2.917,0.229 10 false Instrument Panel Junction Block Assembly 3.26,2.188 6.542,2.656 3.281,0.469 10 false Vehicle Approaching Speaker Controller 3.25,2.021 3.677,2.219 0.427,0.198 10 false L130 0.167,1.396 0.479,1.573 0.313,0.177 10 false 2B 1.604,0.688 2.563,0.927 0.958,0.24 10 false ECU-IG NO. 2 0.365,0.521 1.292,0.99 0.927,0.469 10 false from IG1 NO. 1 Relay 2.667,0.458 2.979,0.635 0.313,0.177 10 false 16 3.646,0.458 3.854,0.625 0.208,0.167 10 false 1 4.74,0.458 4.948,0.625 0.208,0.167 10 false 9 3.927,0.531 4.177,0.698 0.25,0.167 10 false IG 4.271,0.531 4.635,0.708 0.365,0.177 10 false PRST 4.74,1.479 4.948,1.646 0.208,0.167 10 false 7 4.323,1.583 4.615,1.771 0.292,0.188 10 false GND 5.615,0.448 5.802,0.594 0.188,0.146 10 false 7 5.813,0.552 6.115,0.708 0.302,0.156 10 false SIL 6.313,0.552 6.615,0.708 0.302,0.156 10 false CG 6.615,0.448 6.802,0.594 0.188,0.146 10 false 4 5.771,0.948 6.073,1.104 0.302,0.156 10 false L61 5.781,1.083 6.333,1.25 0.552,0.167 10 false DLC3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

The vehicle approaching speaker controller and GTS communicate using SIL communication.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Health Check.

Result:
Result Proceed to
Communication with the vehicle approaching speaker controller is not possible A
Communication with the vehicle approaching speaker controller is possible B




A

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 1 RELAY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 1 RELAY AND BODY GROUND)
a.

Disconnect the L130 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L130-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L130-7 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - DLC3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - DLC3)
a.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L130-9 (PRST) - L61-7 (SIL) Always Below 1 Ω
L130-9 (PRST) or L61-7 (SIL) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-4 (CG) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR