Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.08–2020.08
RM2070E _59 Vehicle Exterior _061962 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0301952 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  Even when Engine is Started or Transmission Shift Main Switch (P Position Switch) is Pushed, Sound does not Stop  


DESCRIPTION

The vehicle approaching speaker controller receives engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the transmission control ECU assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM

E331728E02
3.302,0.438 3.823,0.625 0.521,0.188 10 false OPSW 3.813,0.344 3.99,0.51 0.177,0.167 10 false 12 5.073,0.354 5.25,0.521 0.177,0.167 10 false 1 4.771,0.771 5.063,0.938 0.292,0.167 10 false D26 4.771,0.917 7.146,1.271 2.375,0.354 10 false Engine Oil Pressure Switch Assembly 3.063,1.469 3.531,1.656 0.469,0.188 10 false SFTP 5.229,1.635 5.521,1.823 0.292,0.188 10 false S 4.792,1.906 5.083,2.073 0.292,0.167 10 false D27 4.792,2.063 7.01,2.292 2.219,0.229 10 false Combination Meter Sub-assembly 2.802,1.365 2.979,1.531 0.177,0.167 10 false 11 5.063,1.531 5.26,1.719 0.198,0.188 10 false 6 3.031,0.708 3.417,0.896 0.385,0.188 10 false GND 2.865,0.604 3.042,0.771 0.177,0.167 10 false 7 2.667,1.938 3.031,2.104 0.365,0.167 10 false L130 2.667,2.094 3.99,2.75 1.323,0.656 10 false Vehicle Approaching Speaker Controller 1.323,1.458 1.615,1.646 0.292,0.188 10 false IND 0.219,1.76 0.51,1.927 0.292,0.167 10 false A23 0.219,1.906 2.563,2.135 2.344,0.229 10 false Transmission Control ECU Assembly 1.646,1.375 1.844,1.563 0.198,0.188 10 false 20

PROCEDURE

1.READ VALUE USING GTS (Oil Pressure SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure SW Oil pressure switch / OFF or ON OFF: Engine started
ON: Engine not started
-

Result:
Result Proceed to
The GTS display changes according to engine operation A
The GTS display does not change according to engine operation B




A

2.READ VALUE USING GTS (Shift Position)

B

6.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
2.READ VALUE USING GTS (Shift Position)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift Position P position switch / Not Parking or Parking Not Parking or Parking -

Result:
Result Proceed to
The GTS display changes according to the selected shift state A
The GTS display does not change according to the selected shift state B




A

B

3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
a.

Disconnect the A23 transmission control ECU assembly connector.


b.
U155173E03
1.552,1.396 1.219,1.719 false 0.083,0 0.354,0.208 0.271,0.208 10 false *a 1.604,0.219 1.875,0.385 0.271,0.167 10 false A23 1.031,1.729 1.406,1.938 0.375,0.208 10 false IND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-20 (IND) - Body ground Power switch on (IG) 8 V or higher
Power switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


OK

4.CHECK TRANSMISSION CONTROL ECU ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - TRANSMISSIONCONTROL ECU ASSEMBLY)
4.CHECK TRANSMISSION CONTROL ECU ASSEMBLY
a.

Reconnect the A23 transmission control ECU assembly connector.


b.
U155174E01
0.98,0.261 1.244,0.411 0.264,0.149 10 A23 1.367,1.547 1.631,1.895 false 1.532,1.908 1.796,2.057 0.264,0.149 10 IND 0.124,0.128 0.388,0.277 0.264,0.149 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-20 (IND) - Body ground Power switch on (IG), park (P) selected Below 2.5 V
Power switch on (IG), park (P) not selected 8 V or higher



Text in Illustration
*a Component with harness connected
(Transmission Control ECU Assembly)


OK

NG

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - TRANSMISSIONCONTROL ECU ASSEMBLY)
a.

Disconnect the L130 vehicle approaching speaker controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L130-11 (SFTP) - A23-20 (IND) Always Below 1 Ω
L130-11 (SFTP) or A23-20 (IND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
a.

Disconnect the L130 vehicle approaching speaker controller connector.


b.
U155171E02
2.125,1.427 2.5,1.771 false 1.583,0.24 1.917,0.406 0.333,0.167 10 false L130 2.396,1.781 2.948,1.948 0.552,0.167 10 false OPSW 0.094,0.094 0.427,0.26 0.333,0.167 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L130-12 (OPSW) - Body ground Idling* 8 V or higher
Power switch on (IG) Below 1 V


HINT:

*: Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).



Text in Illustration
*a Front view of wire harness connector
(Vehicle Approaching Speaker Controller)


OK

NG

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OILPRESSURE SWITCH ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OILPRESSURE SWITCH ASSEMBLY)
a.

Disconnect the D26 engine oil pressure switch assembly connector.


b.

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L130-12 (OPSW) - D26-1 Always Below 1 Ω
L130-12 (OPSW) or D26-1 - Body ground Always 10 kΩ or higher




OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR