Use the following procedure to troubleshoot the audio and visual system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the power switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Check that condensation is not likely to occur in the cabin and that the temperature is not high or extremely low in the cabin.
Condensation is not likely being produced and the temperature is not high or extremely low.
A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN DTCs are not output. | A |
| CAN DTCs are output. | B |
A
B
Refer to DTC Check / Clear (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
A
B
Refer to DTC Check / Clear (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to DTC Check / Clear (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
Even if the problem symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the GTS.
Check for DTCs and inspect the area that the code indicates.
A
B
Find the output code in Diagnostic Trouble Code Chart (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Problem Symptoms Table (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PROBLEM SYMPTOMS TABLE).
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table. | A |
| Fault is listed in Problem Symptoms Table. | B |
If the symptoms do not recur and no DTCs are output, attempt to reproduce the symptoms (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
A
B
Refer to Terminals of ECU (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU).
| Proceed to |
|---|
| NEXT |
NEXT
Adjust, repair or replace as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
After clearing DTCs, recheck for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT