Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2016.05
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM Y

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the power window control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in the problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
4.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the LIN communication system is functioning normally (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
No DTCs output A
DTCs output B




A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).


b.

Clear the DTCs.


c.

Recheck for DTCs.

Result:
Result Proceed to
No DTCs output A
DTCs output B




A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B




A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.ADJUST, REPAIR OR REPLACE
7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
a.

Check if any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.

Result:
Result Proceed to
Any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled. A
None of the door window regulators, power window regulator motor assemblies, door glass or door glass runs has been removed and reinstalled. B




A

9.INITIALIZE POWER WINDOW REGULATOR MOTOR

B

10.CONFIRMATION TEST
9.INITIALIZE POWER WINDOW REGULATOR MOTOR
a.

If any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled, perform "Initialize Power Window Control System" (initialization of the pulse sensor) for the applicable door glass (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

HINT:

If "Initialize Power Window Control System" (initialization of the pulse sensor) has not been performed, the auto operation function, jam protection function, and key-off operation function will not operate or will operate incorrectly.



Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END