Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2017.12
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301860 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE

a.

Apply new double-sided tape to locations shown in the illustration while aligning the tape with the markings on the roof headlining.

B274305E01
0.147,1.148 0.346,1.311 0.199,0.163 10 *A 0.147,4.006 0.346,4.169 0.199,0.163 10 *B 1.334,0.915 1.450,1.064 0.116,0.149 10 b 2.6,0.513 2.730,0.662 0.130,0.149 10 c 0.823,0.586 0.939,0.735 0.116,0.149 10 a 0.562,0.112 0.775,0.275 0.213,0.163 10 *C 5.96,0.528 6.076,0.677 0.116,0.149 10 b 1.056,0.272 1.213,0.421 0.157,0.149 10 *1 1.517,0.512 1.215,0.336 false 3.597,1.007 3.754,1.156 0.157,0.149 10 *1 3.663,0.653 3.663,1.001 false 4.344,0.35 4.344,1.027 false 4.541,0.869 4.541,0.957 4.541,0.957 4.344,0.957 false 4.269,1.035 4.427,1.184 0.157,0.149 10 *2

Text in Illustration
*A except Glass Roof *B for Glass Roof
*C Tape Attachment Locations (Reference) - -
*1 Double-sided Tape *2 Marking

Double-sided Tape Size
Item Dimension
a 1 mm (0.0394 in.)
b 10 mm (0.394 in.)
c 20 mm (0.787 in.)

NOTICE:

Securely apply the double-sided tape to prevent it from being out of alignment and peeling off.



b.

Peel off the release paper from the double-sided tape.


c.

Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.


d.

Install the No. 1 roof wire to the roof headlining.

i.

Align the marking tape (A) on the front part of the No. 1 roof wire with the front tab of the roof headlining.

B499859C01
1.396,2.417 1.313,2.292 true 1.396,5.708 1.313,5.583 true 2.313,2.885 2.875,3.01 2.875,3.01 2.521,2.844 true 2.313,6.177 2.875,6.302 2.875,6.302 2.521,6.135 true 2.792,3.292 2.406,3.125 true 2.781,6.563 2.396,6.396 true 2.052,1.25 2.396,1.25 true 2.135,1.604 2.385,1.375 true 2.031,4.521 2.344,4.521 true 4.073,2.302 3.99,2.177 true 4.5,3.042 4.198,2.906 true 4.208,3.177 4.135,3.031 true 3.917,5.844 3.781,5.844 true 4.74,6.229 4.219,6.396 true 4.427,6.698 4.26,6.49 true 0.167,0.167 0.583,0.49 0.417,0.323 12 false *A 0.167,3.406 0.542,3.75 0.375,0.344 12 false *B 1.333,2.427 1.646,2.583 0.313,0.156 10 false *a 2.823,3.208 3.135,3.365 0.313,0.156 10 false *b 4.135,3.177 4.448,3.333 0.313,0.156 10 false *c 4.521,2.948 4.833,3.104 0.313,0.156 10 false *d 0.969,0.656 1.281,0.813 0.313,0.156 10 false *e 3.865,2.083 4.177,2.24 0.313,0.156 10 false *f 3.292,0.469 3.49,0.729 0.198,0.26 10 false *g 5.26,0.49 5.573,0.646 0.313,0.156 10 false *h 5.979,3.958 6.292,4.115 0.313,0.156 10 false *h 3.198,3.948 3.396,4.208 0.198,0.26 10 false *g 3.646,5.75 3.958,5.906 0.313,0.156 10 false *f 0.99,3.979 1.302,4.135 0.313,0.156 10 false *e 4.771,6.135 5.083,6.292 0.313,0.156 10 false *d 4.448,6.625 4.76,6.781 0.313,0.156 10 false *c 2.906,6.208 3.219,6.365 0.313,0.156 10 false *c 2.906,2.917 3.219,3.073 0.313,0.156 10 false *c 2.813,6.49 3.125,6.646 0.313,0.156 10 false *b 1.323,5.708 1.635,5.865 0.313,0.156 10 false *a 1.823,1.146 2.24,1.469 0.417,0.323 12 false *C 1.938,1.521 2.354,1.844 0.417,0.323 12 false *D 1.802,4.427 2.219,4.75 0.417,0.323 12 false *C
*A except Glass Roof *B for Glass Roof
*C w/ EC Mirror or Pre-crash Safety System *D for RHD with Rain Sensor
*a Marking Tape (A) *b Marking Tape (B)
*c Marking *d Joint Box
*e 45° *f Adjustment Area (A)
*g Adjustment Area (B) *h Adjustment Area (C)


HINT:

Align the marking tape (A) with the front tab of the roof headlining so that the part number label is facing the inside of the cabin.



ii.

Align the marking tape (B) on the No. 1 roof wire with the markings on the roof headlining.


iii.

Align the joint box with the roof headlining marking, and secure it using the tape.


iv.

Attach the No. 1 roof wire, starting from the joint box to the marking tape (A) part while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.




v.

Turn the visor connector LH clockwise approximately 45° to install the connector to the roof headlining.


vi.

Attach the No. 1 roof wire, starting from the visor connector LH to the joint box part while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area (A).



vii.

Engage each clamp.


viii.

Turn the visor connector RH clockwise approximately 45° to install the connector to the roof headlining.


ix.

Attach the No. 1 roof wire, starting from the visor connector RH to the clamp while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.




x.

Attach the No. 1 roof wire, starting from the clamp to the adjustment area (B) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.




xi.

Attach the No. 1 roof wire, starting from the joint box to the adjustment area (B) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area (B).



xii.

Attach the No. 1 roof wire, starting from the joint box to the adjustment area (C) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.




xiii.

Attach the No. 1 roof wire, starting from the installation position of the No. 1 room light assembly to the adjustment area (C), while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area (C).




e.

Apply adhesive tape between the markings on the roof headlining.

B499860C01
0.25,5.583 1.917,6.75 1.667,1.167 1.917,5.583 3.25,6.75 1.333,1.167 3.25,5.583 5.083,6.75 1.833,1.167 5.083,5.583 6.917,6.75 1.833,1.167 2.323,0.865 2.625,1.021 true 2.667,5.969 2.833,5.917 true 2.323,6.417 2.49,6.365 true 4.125,6.104 4.396,6.021 true 5.99,6.104 6.323,6 true 0.083,0.083 0.469,0.396 0.385,0.313 12 false *A 0.083,2.844 0.583,3.167 0.5,0.323 12 false *B 4.438,5.917 4.75,6.073 0.313,0.156 10 false *1 0.333,5.667 0.646,5.823 0.313,0.156 10 false *a 0.76,6.49 1.073,6.646 0.313,0.156 10 false *b 1.49,6.073 1.802,6.229 0.313,0.156 10 false *c 2.854,5.823 3.167,5.979 0.313,0.156 10 false *d 3.333,5.667 3.646,5.823 0.313,0.156 10 false *e 5.167,5.667 5.479,5.823 0.313,0.156 10 false *f 3.667,6.438 3.885,6.677 0.219,0.24 10 false *g 2.156,6.333 2.469,6.49 0.313,0.156 10 false *d 6.344,5.896 6.656,6.052 0.313,0.156 10 false *1 4.438,6.417 4.656,6.656 0.219,0.24 10 false *g 2.104,0.74 2.49,1.052 0.385,0.313 12 false *C
*A except Glass Roof *B for Glass Roof
*C w/ EC mirror or Pre-crash Safety System - -
*1 No. 1 Roof Wire - -
*a Adhesive Tape Size *b 20 mm (0.787 in.)
*c 110 mm (4.33 in.) or more *d Marking
*e Correct *f Incorrect
*g 15 mm (0.59 in.) or more - -
V100155

Adhesive Tape - -


HINT:
·

Please avoid holding (touching) the adhesive side as much when taping.

·

Stick the adhesive tape at the position, which No. 1 roof wire would be able to line on the center of tape.

·

If taped on the edge, adhesive width is too small to hold the No. 1 roof wire.

·

After taping, please press all the area of taping with 50 kPa (0.5 kg/cm2,7.25 psi) or more using your finger.




Hide 63343B 2.INSTALL REAR ROOF SILENCER PAD

a.

Align the rear roof silencer pad with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

B282893E03
5.219,0.792 5.438,0.74 true 4.719,1.802 4.719,2.031 true 5.219,3.625 5.438,3.573 true 4.719,4.646 4.719,4.865 true 0.292,0.177 0.49,0.344 0.198,0.167 10 false *A 0.292,3.031 0.49,3.198 0.198,0.167 10 false *B 5.448,0.656 5.604,0.802 0.156,0.146 10 false *2 4.646,2.042 4.802,2.188 0.156,0.146 10 false *1 5.448,3.49 5.604,3.635 0.156,0.146 10 false *2 4.646,4.875 4.802,5.021 0.156,0.146 10 false *1

Text in Illustration
*A except Glass Roof *B for Glass Roof
*1 Hot-melt Glue *2 Marking


Hide 63345D 3.INSTALL CENTER ROOF SILENCER PAD (except Glass Roof)

a.

Align the center roof silencer pad with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

B282891E03
3.948,1.76 3.948,1.958 false 4.469,1.302 4.604,1.302 false 4.615,1.229 4.771,1.375 0.156,0.146 10 false *2 3.865,1.969 4.021,2.115 0.156,0.146 10 false *1

Text in Illustration
*1 Hot-melt Glue *2 Marking


Hide 63341D 4.INSTALL FRONT ROOF SILENCER PAD (except Glass Roof)

a.

Align the front roof silencer pad with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

B282892E03
3.021,2.01 3.021,1.75 false 2.49,2.198 2.49,1.938 false 2.427,2.198 2.583,2.344 0.156,0.146 10 true *2 2.938,2.01 3.094,2.156 0.156,0.146 10 true *1

Text in Illustration
*1 Hot-melt Glue *2 Marking


Hide 81340 5.INSTALL VANITY LIGHT ASSEMBLY

Click hereVehicle Interior>LIGHTING (INT)>VANITY LIGHT>INSTALLATION

HINT:

Use the same procedure for the other vanity light.


Hide 86101J 6.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY