Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339648 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the U15 forward recognition camera connector.



A414025E02
1.948,0.813 2.313,1.063 0.365,0.25 2.01,0.844 2.469,1.042 0.458,0.198 10 false U15

a.

Disconnect the U15 forward recognition camera connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U15-7 (IGB) - U15-10 (GND) V - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
U15-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the U15 forward recognition camera connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U15-1 (HTR) - U15-10 (GND) Y - W-B Forward recognition with heater hood sub-assembly operation signal Power switch on (IG)
Forward recognition with heater hood sub-assembly not operating
11 to 14 V
Power switch on (IG)
Forward recognition with heater hood sub-assembly operating
Below 1 V


e.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U15-5 (CA1P) - U15-10 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
U15-11 (CA1N) - U15-10 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
U15-6 (CANH) - U15-10 (GND) V - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
U15-12 (CANL) - U15-10 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between U15-5 (CA1P) and U15-10 (GND)
Between U15-6 (CANH) and U15-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between U15-11 (CA1N) and U15-10 (GND)
Between U15-12 (CANL) and U15-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.