Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339648 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAE  Heater Circuit  


DESCRIPTION

The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly.

If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE Heater Circuit
Either of the following conditions is met after 2 seconds have elapsed since the power switch was turned on (IG):
·

Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Wire harness or connector



WIRING DIAGRAM

A398326E49
0.115,0.688 3.177,0.885 3.063,0.198 10 false from IG1 NO. 1 Relay 2.094,0.844 3.115,1.073 1.021,0.229 10 false ECU-IG NO. 2 3.167,1.073 5.292,1.49 2.125,0.417 10 false Forward Recognition with Heater Hood Sub-assembly 3.573,0.688 4.031,0.885 0.458,0.198 10 false IG1 4.146,0.688 4.604,0.885 0.458,0.198 10 false HTR 3.396,0.594 3.552,0.792 0.156,0.198 10 false 1 4.5,0.583 4.656,0.781 0.156,0.198 10 false 2 5.344,0.583 5.5,0.781 0.156,0.198 10 false 1 5.531,0.688 5.99,0.885 0.458,0.198 10 false HTR 3.167,0.906 4.083,1.104 0.917,0.198 10 false U14 5,1.917 5.458,2.115 0.458,0.198 10 false U15 5,2.073 6.865,2.302 1.865,0.229 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.





Result:
Result Proceed to
DTC C1AAE is not output A
DTC C1AAE is output B



A

B

2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
a.

Turn the power switch off.


b.
A401973C30
1.698,0.188 2.125,0.438 0.427,0.25 1.688,1.854 1.823,1.26 true 2.188,1.854 2.042,1.271 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.792,0.229 2.25,0.427 0.458,0.198 10 false U14 1.563,1.885 2.021,2.083 0.458,0.198 10 false HTR 2.135,1.885 2.594,2.083 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition with Heater Hood Sub-assembly)


Disconnect the U14 forward recognition with heater hood sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U14-1 (IG1) - U14-2 (HTR) Power switch off 38 to 42 Ω



d.

Connect the U14 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A401974C35
1.552,0.208 1.938,0.448 0.385,0.24 1.125,1.125 1.552,1.219 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.625,0.25 2.083,0.448 0.458,0.198 10 false U14 0.875,1.042 1.333,1.24 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Forward Recognition with Heater Hood Sub-assembly)


Disconnect the U14 forward recognition with heater hood sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U14-1 (IG1) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1.5 V



c.

Connect the U14 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the U14 forward recognition with heater hood sub-assembly connector.


b.

Disconnect the U15 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U14-2 (HTR) - U15-1 (HTR) Always Below 1 Ω
U14-2 (HTR) or U15-1 (HTR) - Body ground Always 10 kΩ or higher



d.

Connect the U15 forward recognition camera connector.


e.

Connect the U14 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)