Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339647 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) U

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the U15 forward recognition camera connector.



A414025E02
1.948,0.813 2.313,1.063 0.365,0.25 2.01,0.844 2.469,1.042 0.458,0.198 10 false U15

a.

Disconnect the U15 forward recognition camera connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U15-7 (IGB) - U15-10 (GND) V - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
U15-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the U15 forward recognition camera connector.


d.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U15-5 (CA1P) - U15-10 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
U15-11 (CA1N) - U15-10 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
U15-6 (CANH) - U15-10 (GND) V - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
U15-12 (CANL) - U15-10 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between U15-5 (CA1P) and U15-10 (GND)
Between U15-6 (CANH) and U15-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between U15-11 (CA1N) and U15-10 (GND)
Between U15-12 (CANL) and U15-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781N80
3.396,0.115 3.833,0.354 0.438,0.24 3.469,0.156 4.083,0.354 0.615,0.198 10 false L205

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L205-7 (B) - L205-28 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
L205-5 (PBSW) - L205-28 (GND) L - W-B Lane departure alert main switch (integration control and panel assembly) signal Power switch off
Lane departure alert main switch off
1 MΩ or higher
Power switch off
Lane departure alert main switch on
Below 1 Ω
L205-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L205-8 (CA1P) - L205-28 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L205-9 (CA1N) - L205-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
L205-10 (CA2H) - L205-28 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L205-11 (CA2L) - L205-28 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between L205-8 (CA1P) - L205-28 (GND)
Between L205-10 (CA2H) - L205-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between L205-9 (CA1N) - L205-28 (GND)
Between L205-11 (CA2L) - L205-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.