Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339647 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  U0101  Lost Communication with TCM  U0123  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  U0131  Lost Communication with Power Steering Control Module  U0142  Lost Communication with Body Control Module "B"  U0155  Lost Communication with Combination Meter  U0293  Lost Communication with HV ECU  


DESCRIPTION

When a malfunction is detected between various ECUs and sensors, these DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0101 Lost Communication with TCM 2 seconds after the power switch is turned on (IG), while the vehicle is being driven at 1 km/h or 1 mph or more, a communication error between the TCM (hybrid vehicle control ECU) and the forward recognition camera is detected for approximately 5 seconds or more. CAN communication system
U0123 Lost Communication with Yaw Rate Sensor Module 2 seconds after the power switch is turned on (IG), while the vehicle is being driven at 1 km/h or 1 mph or more, a communication error between the yaw rate sensor (airbag ECU assembly) and the forward recognition camera is detected for approximately 5 seconds or more. CAN communication system
U0126 Lost Communication with Steering Angle Sensor Module 2 seconds after the power switch is turned on (IG), a communication error between the steering sensor (spiral cable with sensor sub-assembly) and the forward recognition camera is detected for approximately 5 seconds or more. CAN communication system
U0129 Lost Communication with Brake System Control Module 2 seconds after the power switch is turned on (IG), a communication error between the skid control ECU (brake booster with master cylinder assembly) and the forward recognition camera is detected for approximately 5 seconds or more. CAN communication system
U0131 Lost Communication with Power Steering Control Module 2 seconds after the power switch is turned on (IG), a communication error between the power steering ECU assembly and the forward recognition camera is detected for approximately 5 seconds or more. CAN communication system
U0142 Lost Communication with Body Control Module "B" 2 seconds after the power switch is turned on (IG), a communication error between the main body ECU (multiplex network body ECU) and the forward recognition camera is detected for approximately 5 seconds or more. CAN communication system
U0155 Lost Communication with Combination Meter 2 seconds after the power switch is turned on (IG), a communication error between the combination meter sub-assembly and the forward recognition camera is detected for approximately 50 seconds or more. CAN communication system
U0293 Lost Communication with HV ECU 2 seconds after the power switch is turned on (IG), a communication error between the hybrid vehicle control ECU and the forward recognition camera is detected for approximately 5 seconds. CAN communication system

PROCEDURE

1.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 1 minute or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.





Result:
Result Proceed to
DTC U0101, U0123, U0126, U0129, U0131, U0142, U0155 and U0293 are not output A
DTC U0101, U0123, U0126, U0129, U0131, U0142, U0155 or U0293 is output B



A

B