Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339647 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

E376695E13
4.917,2.688 6.854,2.938 1.938,0.25 10 false Forward Recognition Camera 2.708,1.083 3.917,1.323 1.208,0.24 10 false ECU-IG NO. 2 5.302,0.906 5.719,1.094 0.417,0.188 10 false IGB 5.302,1.948 5.719,2.135 0.417,0.188 10 false GND 5.083,0.792 5.5,0.979 0.417,0.188 10 false 7 5.031,1.813 5.448,2 0.417,0.188 10 false 10 4.906,2.521 5.323,2.708 0.417,0.188 10 false U15 0.354,0.896 2.292,1.146 1.938,0.25 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A410116C15
1.531,0.167 1.948,0.385 0.417,0.219 0.948,1.563 1.271,1.417 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a 0.677,1.51 1.177,1.74 0.5,0.229 10 false IGB 1.615,0.198 2.115,0.427 0.5,0.229 10 false U15
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U15-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Connect the U15 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
A410116C16
1.531,0.167 1.948,0.385 0.417,0.219 1.615,1.823 1.781,1.417 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a 1.448,1.844 1.948,2.073 0.5,0.229 10 false GND 1.615,0.198 2.115,0.427 0.5,0.229 10 false U15
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U15-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the U15 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR