Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781N80
3.396,0.115 3.833,0.354 0.438,0.24 3.469,0.156 4.083,0.354 0.615,0.198 10 false L205

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L205-7 (B) - L205-28 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
L205-3 (BZ) - L205-28 (GND) L - W-B Skid control buzzer assembly output Power switch on (IG), buzzer not sounding 11 to 14 V
Power switch on (IG), buzzer sounding Below 1 V
L205-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L205-8 (CA1P) - L205-28 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L205-9 (CA1N) - L205-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
L205-10 (CA2H) - L205-28 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L205-11 (CA2L) - L205-28 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between L205-8 (CA1P) - L205-28 (GND)
Between L205-10 (CA2H) - L205-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between L205-9 (CA1N) - L205-28 (GND)
Between L205-11 (CA2L) - L205-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


E321782N62
2.167,0.75 2.583,1 0.417,0.25 2.26,0.792 2.719,0.99 0.458,0.198 10 false A91

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A91-8 (IGB) - A91-1 (SGND) R - W-B Power source Power switch on (IG) 11 to 14 V
A91-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the millimeter wave radar sensor assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A91-3 (CA2H) - A91-1 (SGND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A91-2 (CA2L) - A91-1 (SGND) BR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A91-5 (CA1P) - A91-1 (SGND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A91-6 (CA1N) - A91-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between A91-3 (CA2H) and A91-1 (SGND)
Between A91-5 (CA1P) and A91-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between A91-2 (CA2L) and A91-1 (SGND)
Between A91-6 (CA1N) and A91-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.