Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status ON or OFF ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status ON or OFF ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-crash safety system on/off status ON or OFF ON: Pre-crash safety system on
OFF: Pre-crash safety system off
-
Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash braking function Valid or Inval Valid: Pre-crash braking operation possible
Inval: Pre-crash braking operation not possible
-
PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-crash brake assist not operating
Standby: Brake pedal not depressed during pre-crash brake assist operation
Assist Lv1: Brake pedal depressed during pre-crash brake assist operation
Assist Lv2: Brake pedal firmly depressed during pre-crash brake assist operation
Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake - - - Not applicable to the vehicle
Brake Assist Standby - - - This item is displayed on the GTS but is not used.
Pre-Crash Brake Control Pre-crash braking operational status ON or OFF ON: Pre-crash braking operating
OFF: Pre-crash braking not operating
-
AVS Start - - - Not applicable to the vehicle
VGRS Start - - - Not applicable to the vehicle
PBA Control Pre-crash brake assist operational status Valid or Invalid Valid: Pre-crash brake assist control operation possible
Invalid: Pre-crash brake assist control operation not possible
-
Pre-Crash Safety Brake Ind Pre-crash safety system alarm warning message status ON or OFF ON: Displayed
OFF: Not displayed
"BRAKE!" is displayed
PCS Crash Alarm Buzzer Skid control buzzer assembly status ON or OFF ON: Skid control buzzer assembly sounding
OFF: Skid control buzzer assembly not sounding
-
Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history ON or OFF ON: History of excessive dirt
OFF: No history of excessive dirt
-
Front Radar-Temperature Malfunction History Millimeter wave radar sensor assembly abnormal temperature history ON or OFF ON: History of abnormal temperature
OFF: No history of abnormal temperature
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF ON: History of low voltage
OFF: No history of low voltage
-
Front Radar-Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history ON or OFF ON: History of vertical misalignment
OFF: No history of vertical misalignment
If "PRE-CRASH SAFETY UNAVAILABLE" is displayed on the multi-information display and there is front beam axis misalignment (vertical) history, the millimeter wave radar sensor assembly may be performing beam axis alignment correction. In this case, perform Front Beam Axis Adjustment to return the system to normal.
Front Radar-Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history ON or OFF ON: History of horizontal misalignment
OFF: No history of horizontal misalignment
-
Front Recognition Camera-Blockage History Forward recognition camera obstruction history ON or OFF ON: History of being obstructed
OFF: No history of being obstructed
-
Front Recognition Camera-Malfunction History Forward recognition camera system unavailable history ON or OFF ON: History of unavailable
OFF: No history of unavailable
-
Driving Support ECU Destination Variation No Destination country for driving support computer Destination Variation No or Not Available Actual country code -
Control Mode ECU control mode status ON or OFF Normal: Normal operation
Check: Operating in Control Mode
-
PCS Operation State Retention Setting PCS Operation State Retention Setting customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
The Number of DTCs Number of trouble codes 0 to 255 Number of DTCs will be displayed -



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with power switch on (IG), vehicle stopped


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light switch (Stop light switch assembly) ON / OFF Stop lights come on