Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A Lost Communication with Front Camera Module When the power switch is on (IG), a communication error between the forward recognition camera and driving support ECU assembly is detected for approximately 3 seconds.
·

Forward recognition camera branch line or connector

·

Forward recognition camera power source circuit

·

Forward recognition camera



WIRING DIAGRAM

B429438E85
0.188,1.833 2.427,2.125 2.24,0.292 10 false CAN Junction Connector 0.188,1.667 0.646,1.865 0.458,0.198 10 false L204 1.635,0.771 1.906,0.969 0.271,0.198 10 false 2 1.635,1.354 1.948,1.552 0.313,0.198 10 false 13 5.406,0.76 5.563,0.958 0.156,0.198 10 false 6 5.344,1.365 5.594,1.563 0.25,0.198 10 false 12 5.406,2.615 5.563,2.813 0.156,0.198 10 false 7 5.333,3.385 5.635,3.594 0.302,0.208 10 false 10 5.573,0.875 6.188,1.073 0.615,0.198 10 false CANH 5.573,1.469 6.188,1.667 0.615,0.198 10 false CANL 5.573,2.708 6.031,2.906 0.458,0.198 10 false IGB 5.563,3.49 6.177,3.688 0.615,0.198 10 false GND 1.156,2.708 2.813,2.917 1.656,0.208 10 false from IG1 NO. 1 Relay 5.167,4.042 7.021,4.26 1.854,0.219 10 false Forward Recognition Camera 5.167,3.875 5.625,4.073 0.458,0.198 10 false U15 3.729,2.865 5.021,3.104 1.292,0.24 10 false ECU-IG NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 3 seconds or more.





Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

3.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)

B

3.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A410116C14
1.531,0.167 1.948,0.385 0.417,0.219 2.146,1.125 2.396,0.99 true 2.167,1.427 2.406,1.51 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a 2.448,0.875 2.948,1.104 0.5,0.229 10 false CANH 2.448,1.438 2.948,1.667 0.5,0.229 10 false CANL 1.615,0.198 2.115,0.427 0.5,0.229 10 false U15
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U15-6 (CANH) - U15-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



d.

Connect the U15 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A410116C17
1.531,0.167 1.948,0.385 0.417,0.219 0.948,1.573 1.271,1.417 true 1.823,1.813 1.781,1.427 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a 1.677,1.823 2.177,2.052 0.5,0.229 10 false GND 1.615,0.198 2.115,0.427 0.5,0.229 10 false U15 0.677,1.51 1.177,1.74 0.5,0.229 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U15-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U15-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V



e.

Connect the U15 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)