Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the driving support ECU assembly when the power switch is on (IG).

WIRING DIAGRAM

E376695E09
4.823,2.698 6.76,2.948 1.938,0.25 10 false Driving Support ECU Assembly 2.708,1.073 3.792,1.281 1.083,0.208 10 false ECU-IG NO. 2 5.302,0.906 5.719,1.094 0.417,0.188 10 false B 5.302,1.948 5.719,2.135 0.417,0.188 10 false GND 5.083,0.792 5.5,0.979 0.417,0.188 10 false 7 5.031,1.813 5.448,2 0.417,0.188 10 false 28 4.833,2.531 5.25,2.719 0.417,0.188 10 false L205 0.354,0.896 2.292,1.146 1.938,0.25 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
A418460C03
1.583,0.167 2,0.417 0.417,0.25 1.25,0.948 0.917,0.365 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.792,0.281 0.948,0.479 0.156,0.198 10 false B 1.646,0.208 2.26,0.406 0.615,0.198 10 false L205
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the L205 driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L205-7 (B) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the L205 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
A418460C04
1.583,0.167 2,0.417 0.417,0.25 2.469,1.281 2.302,1.865 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.979,1.792 2.438,1.99 0.458,0.198 10 false GND 1.646,0.208 2.26,0.406 0.615,0.198 10 false L205
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the L205 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L205-28 (GND) - Body ground Always Below 1 Ω



c.

Connect the L205 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR