Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › from 2017.12
RM2070E _59 Vehicle Exterior _061955 EXTERIOR PANELS / TRIM _0301933 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

When install new name plates or side panel emblem, heat the back door panel and name plates or side panel emblem using a heat light.

Heating Temperature
Item Temperature
Back Door Panel 40 to 60°C (104 to 140°F)
Name Plate or Back Door Emblem 20 to 30°C (68 to 86°F)


CAUTION:
·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door panel, back door name plates or side panel emblem excessively.


PROCEDURE

Hide 75431A 1.INSTALL NO. 1 BACK DOOR EMBLEM

a.

Engage the pin and 3 claws to install the No. 1 back door emblem.


b.

Install the back door outside garnish sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BACK DOOR OUTSIDE GARNISH>INSTALLATION


Hide 75442A 2.INSTALL NO. 2 BACK DOOR NAME PLATE

a.

Clean the back door panel surface.

i.

Using a heat light, heat the back door panel surface.


ii.

Remove any remaining double-sided tape from the back door panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door panel and a new No. 2 back door name plate.


c.

Remove the release paper from the No. 2 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 2 back door name plate as shown in the illustration.

for Type A:

B283944C01
3.552,2.042 3.865,2.042 false 3.385,1.958 3.688,2.24 0.302,0.281 10 false *a 3.854,1.281 4.042,1.531 0.188,0.25 10 false A 3.969,2.573 4.156,2.74 0.188,0.167 10 false B 6.01,1.469 6.198,1.719 0.188,0.25 10 false C 6.229,1.781 6.417,2.031 0.188,0.25 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 168.7 mm (6.64 in.) B 17.2 mm (0.677 in.)
C 95.1 mm (3.74 in.) D 23.0 mm (0.906 in.)


NOTICE:

Press the No. 2 back door name plate firmly to install it.


for Type B:

B501320C01
3.469,1.448 3.885,1.448 false 3.281,1.365 3.75,1.76 0.469,0.396 10 false *a 3.917,1.063 4.177,1.385 0.26,0.323 10 false A 4.031,2.542 4.24,2.781 0.208,0.24 10 false B 5.802,1.25 6.063,1.573 0.26,0.323 10 false C 6.198,1.552 6.458,1.875 0.26,0.323 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 168.7 mm (6.64 in.) B 17.2 mm (0.677 in.)
C 90.2 mm (3.55 in.) D 18.3 mm (0.720 in.)


NOTICE:

Press the No. 2 back door name plate firmly to install it.


for Type C:

B501344C01
3.51,1.135 3.854,1.135 false 3.302,1.052 3.688,1.354 0.385,0.302 10 false *a 3.938,1.021 4.24,1.323 0.302,0.302 10 false A 4.031,2.51 4.292,2.719 0.26,0.208 10 false B 6.115,1.198 6.375,1.406 0.26,0.208 10 false C 6.281,1.625 6.542,1.833 0.26,0.208 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 168.7 mm (6.64 in.) B 17.2 mm (0.677 in.)
C 97.7 mm (3.85 in.) D 15.0 mm (0.591 in.)


NOTICE:

Press the No. 2 back door name plate firmly to install it.



Hide 75441E 3.INSTALL NO. 1 BACK DOOR NAME PLATE

a.

Clean the back door panel surface.

i.

Using a heat light, heat the back door panel surface.


ii.

Remove any remaining double-sided tape from the back door panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door panel and a new No. 1 back door name plate.


c.

Remove the release paper from the No. 1 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Install the No. 1 back door name plate as shown in the illustration.

B500624C01
6.583,2.375 6.781,2.375 false 6.781,2.26 7.052,2.583 0.271,0.323 10 false *a 4.26,2.552 4.521,2.75 0.26,0.198 10 false A 4.479,1.5 4.74,1.698 0.26,0.198 10 false B 5.844,1.344 6.104,1.542 0.26,0.198 10 false C 6.271,2.01 6.531,2.208 0.26,0.198 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 49.6 mm (1.95 in.) B 128.3 mm (5.05 in.)
C 137.7 mm (5.42 in.) D 54.1 mm (2.13 in.)


NOTICE:

Press the No. 1 back door name plate firmly to install it.



Hide 75374 4.INSTALL SIDE PANEL EMBLEM (for LH Side)

a.

Clean the side panel surface.

i.

Using a heat light, heat the side panel surface.


ii.

Remove any remaining double-sided tape from the side panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install the side panel emblem.

i.

Using a heat light, heat the vehicle body and a new side panel emblem.


ii.

Remove the release paper from the side panel emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

w/ Location Pin:

1.

Engage the 2 pins to install the side panel emblem as shown in the illustration.

B283943C01
4.979,1.771 5.281,2.208 5.281,2.208 5.542,1.76 true 5.198,2.229 5.469,2.51 0.271,0.281 10 false *a
*a Location Pin - -




iv.

w/o Location Pin:

1.

Install the side panel emblem as shown in the illustration.

B598122C01
4.083,1.406 4.354,1.25 false 6.438,1.469 6.021,1.365 true 3.927,1.323 4.24,1.521 0.313,0.198 10 false *a 4.729,1.313 5.042,1.51 0.313,0.198 10 false A 5.688,1.198 6,1.396 0.313,0.198 10 false B 6.125,1 6.26,1.177 0.135,0.177 10 true C 6.469,1.385 6.781,1.583 0.313,0.198 10 false *a
*a R End - -


Standard Measurement:
Area Measurement Area Measurement
A 53.6 mm (2.11 in.) B 31.5 mm (1.24 in.)
C 44.4 mm (1.75 in.) - -



NOTICE:

Press the side panel emblem firmly to install it.




Hide 75374 5.INSTALL SIDE PANEL EMBLEM (for RH Side)

a.

Clean the side panel surface.

i.

Using a heat light, heat the side panel surface.


ii.

Remove any remaining double-sided tape from the side panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install the side panel emblem.

i.

Using a heat light, heat the vehicle body and a new side panel emblem.


ii.

Remove the release paper from the side panel emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

w/ Location Pin:

1.

Engage the 2 pins to install the side panel emblem as shown in the illustration.

B598225C01
5.469,1.698 5.677,2.083 5.677,2.083 5.938,1.635 true 5.594,2.115 5.865,2.396 0.271,0.281 10 false *a
*a Location Pin - -




iv.

w/o Location Pin:

1.

Install the side panel emblem as shown in the illustration.

B598226C01
4.365,1.24 4.635,1.083 false 6.417,1.479 6,1.375 true 5.354,1.75 4.948,1.5 true 4.156,1.146 4.469,1.344 0.313,0.198 10 false *a 4.771,1.823 5.083,2.021 0.313,0.198 10 false A 4.885,1.198 5.198,1.396 0.313,0.198 10 false B 6.24,1.167 6.375,1.344 0.135,0.177 10 true C 6.438,1.406 6.75,1.604 0.313,0.198 10 false *a 5.375,1.698 5.688,1.896 0.313,0.198 10 false *a
*a R End - -


Standard Measurement:
Area Measurement Area Measurement
A 36.2 mm (1.43 in.) B 55.8 mm (2.10 in.)
C 29.7 mm (1.17 in.) - -



NOTICE:

Press the side panel emblem firmly to install it.