Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2017.12–2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U190956E02
1.865,0.698 2.219,0.865 0.354,0.167 10 false L195 3.271,0.698 3.625,0.865 0.354,0.167 10 false L196 4.854,0.708 5.208,0.875 0.354,0.167 10 false L197

a.

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
L195-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
L195-2 (+B) - L195-11 (E) Input B - W-B +B power supply Power switch off 11 to 14 V -
L195-10 (CUTB) - L195-11 (E) Input R - W-B Dark current cut pin* Power switch off 11 to 14 V -

*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds that form the detection area stops).


If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.


c.

Reconnect the L195 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
L197-5 (IG) - L195-11 (E) Input P - W-B GR power supply Power switch off → on (IG) Below 1 V → 11 to 14 V Ignition Switch
L197-12 (CLG1) - L195-11 (E) Output L - W-B*4
G - W-B*5
Output to driver door electrical key antenna (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Driver Side (key diagnostic mode)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
L197-13 (CG1B) - L195-11 (E) Output Y - W-B*4
R - W-B*5
Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
L197-11 (CLG2) - L195-11 (E)*6 Output G - W-B*4
L - W-B*5
Output to front passenger door electrical key antenna (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Passenger Side (key diagnostic mode)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
L197-10 (CG2B) - L195-11 (E)*6 Output R - W-B*4
Y - W-B*5
Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
L197-3 (CLG5) - L195-11 (E) Output V - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
L197-2 (CG5B) - L195-11 (E) Output L - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
L197-20 (TSW1) - L195-11 (E) Input G - W-B*4
W - W-B*5
Driver door lock sensor signal input (Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly).
Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 20 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 5) D-Door Trigger Switch
L197-8 (TSW2) - L195-11 (E)*6 Input W - W-B*4
G - W-B*5
Front passenger door lock sensor signal input (Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly).
Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 20 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched


Pulse generation (See waveform 5) P-Door Trigger Switch
L197-22 (SEN1) - L195-11 (E) Input V - W-B*4
Y - W-B*5
Driver door unlock sensor signal input (when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation (See waveform 5) D-Door Touch Sensor
L197-23 (SEN2) - L195-11 (E)*6 Input Y - W-B*4
V - W-B*5
Front passenger door unlock sensor signal input (when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation (See waveform 5) P-Door Touch Sensor
L196-27 (TSW5) - L195-11 (E)*6 Input GR - W-B Back door opener switch assembly (unlock switch) signal input Back door opener switch assembly (unlock switch) off → on Pulse generation (See waveform 5) Tr/B-Door Unlock SW
L196-28 (TSW6) - L195-11 (E)*6 Input B - W-B Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch )off → on Pulse generation (See waveform 5) Tr/B-Door Lock SW
L196-11 (CLG6) - L195-11 (E) Output P - W-B Output to No. 3 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
L196-10 (CG6B) - L195-11 (E) Output BR - W-B Output to No. 3 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
L196-9 (CLG7) - L195-11 (E) Output V - W-B Output to No. 2 indoor electrical key antenna assembly (inside luggage) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Back Door (inside) (key diagnostic mode)
L196-8 (CG7B) - L195-11 (E) Output R - W-B Output to No. 2 indoor electrical key antenna assembly (inside luggage) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Back Door (inside) (key diagnostic mode)
L197-19 (POS1) - L195-11 (E) Output GR - W-B*4
SB - W-B*5
Driver door unlock sensor power source (12 V (drops when power switch turned on (IG))) Power switch off → on (IG) 9 to 14 V → Below 2 V -
L197-21 (POS2) - L195-11 (E)*6 Output SB - W-B*4
GR - W-B*5
Front passenger door unlock sensor power source (12 V (drops when power switch turned on (IG))) Power switch off → on (IG) 9 to 14 V → Below 2 V -
L196-5 (RCO) - L195-11 (E) Output LG - W-B Output to door control receiver (Power supply for door control receiver.
Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 6) -
L196-17 (RDAM) - L195-11 (E) Input GR - W-B*7
Y - W-B*8
Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Proceed:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 7) -
L196-6 (CSEL) - L195-11 (E) Output V - W-B*7
SB - W-B*8
Communication channel switching circuit Procedure:
1.

Power switch off

2.

All doors closed


Below 1 V → Pulse generation Key diagnostic mode
L196-2 (CLG8) - L195-11 (E)*6 Output G - W-B Output to electrical key antenna (outside luggage) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation (See waveform 4) Over Head + Back Door
L196-1 (CG8B) - L195-11 (E)*6 Output P - W-B Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation (See waveform 4) Over Head + Back Door

*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

*4: for LHD

*5: for RHD

*6: w/ Entry Function

*7: w/ Tire Pressure Warning System

*8: w/o Tire Pressure Warning System



e.
B251021E22
0.177,1.01 0.51,1.208 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection L197-12 (CLG1) - L195-11 (E)
L197-11 (CLG2) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



f.
B251024E04
0.177,1.052 0.844,1.458 0.667,0.406 10 false GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection L197-12 (CLG1) - L195-11 (E)
L197-11 (CLG2) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).


Waveform 2 (Reference)
Item Content
Tester Connection L197-13 (CG1B)- L195-11 (E)
L197-10 (CG2B)- L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



g.
B251020E04
0.844,1.885 1.031,2.094 0.188,0.208 10 false *a 1.771,1.885 1.958,2.094 0.188,0.208 10 false *b 0.167,1.01 0.5,1.208 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Door open
*b After approximately 30 seconds from when the door is closed

Waveform 3 (Reference)
Item Content
Tester Connection L197-3 (CLG5) - L195-11 (E)
L197-2 (CG5B) - L195-11 (E)
L196-11 (CLG6) - L195-11 (E)
L196-10 (CG6B) - L195-11 (E)
L196-9 (CLG7) - L195-11 (E)
L196-8 (CG7B) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds




h.
B265917E09
0.104,1.01 0.427,1.146 0.323,0.135 10 false GND 1.188,1.969 1.344,2.104 0.156,0.135 10 false *a

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Power switch off, all doors closed and Back Door Opener Switch Assembly off → on

Waveform 4 (Reference)
Item Content
Tester Connection L196-2 (CLG8) - L195-11 (E)
L196-1 (CG8B) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on




i.
B251023E18
1.344,0.49 2,0.125 2,0.125 2.219,0.125 true 2.01,0.125 1.76,0.5 true 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.26,0.042 2.438,0.219 0.177,0.177 10 false *a

Using an oscilloscope, check waveform 5.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a In actuality, sampling is being performed

Waveform 5 (Reference)
Item Content
Tester Connection L197-20 (TSW1) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection L197-8 (TSW2) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection L197-22 (SEN1) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection L197-23 (SEN2) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection L196-27 (TSW5) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Back door opener switch assembly (unlock switch) off → on

Waveform 5 (Reference)
Item Content
Tester Connection L196-28 (TSW6) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Back door opener switch assembly (lock switch) off → on


j.
B251178E04
0.177,1 0.51,1.198 0.333,0.198 10 false GND 0.969,1.885 1.156,2.042 0.188,0.156 10 false *a 2.01,1.885 2.198,2.042 0.188,0.156 10 false *b

Using an oscilloscope, check waveform 6.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock switch of Electrical Key Transmitter Sub-assembly pressed
*b After lock or unlock switch of Electrical Key Transmitter Sub-assembly pressed

Waveform 6 (Reference)
Item Content
Tester Connection L196-5 (RCO) - L195-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).



k.
B251177E05
0.156,1.01 0.49,1.208 0.333,0.198 10 false GND 0.979,1.875 1.167,2.031 0.188,0.156 10 false *a 2.198,1.875 2.385,2.031 0.188,0.156 10 false *b

Using an oscilloscope, check waveform 7.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock switch of Electrical Key Transmitter Sub-assembly pressed
*b After lock or unlock switch of Electrical Key Transmitter Sub-assembly pressed

Waveform 7 (Reference)
Item Content
Tester Connection L196-17 (RDAM) - L195-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).




CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U190878E03
1.781,0.677 1.625,0.677 1.625,0.677 1.625,0.958 true 1.531,1.448 1.448,1.448 1.448,1.448 1.448,3.323 true 1.542,1.76 1.458,1.76 false 1.542,2.104 1.458,2.104 false 0.698,2.771 1.021,2.771 true 3.167,7.583 3.458,7.75 0.292,0.167 10 false MB 4.875,6.375 5.167,6.542 0.292,0.167 10 false 2A 1.875,6.375 2.167,6.542 0.292,0.167 10 false 2B 1.177,5.104 1.469,5.271 0.292,0.167 10 false 2D 0.531,1.5 0.823,1.667 0.292,0.167 10 false 2D 3.927,5.135 4.219,5.302 0.292,0.167 10 false 2C 0.531,2.156 0.823,2.323 0.292,0.167 10 false 2C 4.802,3.792 5.188,4 0.385,0.208 10 false L201 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.583,5.104 5.875,5.271 0.292,0.167 10 false 2E 5.885,5.104 6.094,5.271 0.208,0.167 10 false *B 6.563,5.125 6.771,5.292 0.208,0.167 10 false *C 2.354,3.802 2.76,4 0.406,0.198 10 false L190 0.26,2.563 0.552,2.729 0.292,0.167 10 false 2E 0.563,2.552 0.854,2.719 0.292,0.167 10 false *A 0.573,2.865 0.865,3.031 0.292,0.167 10 false *B 0.271,2.844 0.563,3.01 0.292,0.167 10 false 2F 1.948,1.698 2.344,1.896 0.396,0.198 10 false L201 1.938,2.063 2.313,2.25 0.375,0.188 10 false L190 6.292,1.542 6.5,1.708 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.281,2.188 6.49,2.354 0.208,0.167 10 false 2A 1.844,0.604 2,0.76 0.156,0.156 10 false *1 1.375,3.344 1.531,3.5 0.156,0.156 10 false *2

Text in Illustration
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors

a.

Remove the main body ECU from the instrument panel junction block assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - None - Body ground Ground Always Below 1 Ω -
L190-3 (GND2) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
MB-30 (BECU) - Body ground Input None - Body ground Auxiliary battery power supply (for CPU) Power switch off 11 to 14 V -
MB-31 (ALTB) - Body ground Input None - Body ground Auxiliary battery power supply (for indicator) Power switch off 11 to 14 V -
MB-29 (ACC) - Body ground Input None - Body ground ACC power supply Power switch on (ACC) 11 to 14 V ACC SW
MB-32 (IG) - Body ground Input None - Body ground Power switch power supply Power switch on (IG) 11 to 14 V IG SW

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU to the instrument panel junction block assembly.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
2D-36 (FRCY) - Body ground Input BR*1 - Body ground
V*2 - Body ground
Front door RH courtesy light switch input Front door RH open Below 1 V FR Door Courtesy
Front door RH closed 11 to 14 V
2D-35 (FLCY) - Body ground Input Y*1 - Body ground
V*2 - Body ground
Front door LH courtesy light switch input Front door LH open Below 1 V FL Door Courtesy
Front door LH closed 11 to 14 V
L201-6 (LRCY) - Body ground Input G - Body ground Rear door LH and RH courtesy light switch input Rear door LH or RH open Below 1 V RL Door Courtesy SW
Rear door LH and RH closed 11 to 14 V RR Door Courtesy SW
L201-19 (BCTY) - Body ground Input L - Body ground Back door courtesy light switch input Back door open Below 1 V Back Door Courtesy SW
Back door closed and luggage compartment light switch on 11 to 14 V
Back door closed and luggage compartment light switch off Pulse generation (See waveform 1 or 2)
2B-8 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2B-9 (ACT+) - Body ground Output R - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2B-10 (ACT+) - Body ground Output P - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2D-12 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2B-1 (ACT-) - Body ground Output B - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
2D-11 (ACT-) - Body ground Output V - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
2B-3 (ACT-) - Body ground Output LG - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
L201-7 (LSFL) - Body ground Input GR - Body ground Front door LH lock position switch input Front door LH unlocked Below 1 V FL Door Lock Pos
Power switch off, all doors closed and front door LH locked Pulse generation (See waveform 1 or 2)
L201-18 (LSFR) - Body ground Input LG - Body ground Front door RH lock position switch input Front door RH unlocked Below 1 V FR Door Lock Pos
Power switch off, all doors closed and front door RH locked Pulse generation (See waveform 3 or 4)
2D-25 (LSR) - Body ground Input GR - Body ground Rear door LH lock position switch input Rear door LH or RH unlocked Below 1 V RL-Door Lock Pos SW
Power switch off, all doors closed and rear door LH and RH locked Pulse generation (See waveform 3 or 4)
2B-29 (LSR) - Body ground Input GR - Body ground Rear door RH lock position switch input Rear door RH or LH unlocked Below 1 V RR-Door Lock Pos SW
Power switch off, all doors closed and rear door RH and LH locked Pulse generation (See waveform 3 or 4)

*:1 for LHD

*:2 for RHD


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) L201-19 (BCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Back door closed and luggage compartment light switch off

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) L201-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door LH locked


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) L201-19 (BCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Back door closed and luggage compartment light switch off

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) L201-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door LH locked


g.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) L201-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door RH locked

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) 2D-25 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door LH and RH locked

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) 2B-29 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door RH and LH locked


h.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) L201-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door RH locked

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) 2D-25 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door LH and RH locked

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) 2B-29 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door RH and LH locked