Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.12
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


a.

Disconnect the O6*1 or N13*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD


U190803C01
3.063,0.156 3.344,0.365 0.281,0.208 10 false O6 3.354,0.156 3.885,0.802 0.531,0.646 10 false *A 3.667,0.167 4.031,0.417 0.365,0.25 10 false N13 3.99,0.146 4.438,0.427 0.448,0.281 10 false *B
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-11 (B) - O6-12 (GND) W - W-B Power supply Power switch off 11 to 14 V
O6-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N13-11 (B) - N13-12 (GND) W - W-B Power supply Power switch off 11 to 14 V
N13-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O6*1 or N13*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-15 (DOWN) - O6-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
O6-15 (DOWN) - O6-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
O6-18 (LED) - O6-12 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O6-18 (LED) - O6-12 (GND) Y - W-B LED illumination signal Power switch off Below 1 V
O6-20 (UP) - O6-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
O6-20 (UP) - O6-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N13-15 (DOWN) - N13-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
N13-15 (DOWN) - N13-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
N13-18 (LED) - N13-12 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N13-18 (LED) - N13-12 (GND) Y - W-B LED illumination signal Power switch off Below 1 V
N13-20 (UP) - N13-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
N13-20 (UP) - N13-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


a.

Disconnect the N7*1 or O13*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD


U190805C01
3.094,0.333 3.292,0.479 0.198,0.146 10 false N7 3.406,0.333 3.604,0.479 0.198,0.146 10 false *A 3.688,0.333 3.969,0.479 0.281,0.146 10 false O13 4.052,0.333 4.25,0.479 0.198,0.146 10 false *B
*A for LHD *B for RHD



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O13-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the N7*1 or O13*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-4 (LED) - N7-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N7-4 (LED) - N7-1 (GND) GR - W-B LED illumination signal Power switch off Below 1 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O13-4 (LED) - O13-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O13-4 (LED) - O13-1 (GND) GR - W-B LED illumination signal Power switch off Below 1 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)


a.

Disconnect the Q2 rear power window regulator switch assembly (for LH door) connector.

U154531N01
3.479,0.333 3.99,0.708 0.51,0.375 10 false Q2


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the Q2 rear power window regulator switch assembly (for LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q2-4 (LED) - Q2-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
Q2-4 (LED) - Q2-1 (GND) Y - W-B LED illumination signal Power switch off Below 1 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


a.

Disconnect the P2 rear power window regulator switch assembly (for RH door) connector.

U154532N01
3.49,0.333 3.75,0.521 0.26,0.188 10 false P2


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the P2 rear power window regulator switch assembly (for RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P2-4 (LED) - P2-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
P2-4 (LED) - P2-1 (GND) GR - W-B LED illumination signal Power switch off Below 1 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


a.

Disconnect the O2*1 or N2*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD


U190845C01
2.25,0.688 2.563,0.969 0.313,0.281 10 false O2 2.542,0.698 2.865,1.01 0.323,0.313 10 false *A 2.26,0.969 2.563,1.24 0.302,0.271 10 false N2 2.552,0.979 2.76,1.219 0.208,0.24 10 false *B
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
O2-2 (B) - Body ground W - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
N2-2 (B) - Body ground W - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the O2*1 or N2*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-5 (LED) - O2-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O2-5 (LED) - O2-1 (GND) Y - W-B LED illumination signal Power switch off Below 1 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation) Below 1 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-5 (LED) - N2-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N2-5 (LED) - N2-1 (GND) Y - W-B LED illumination signal Power switch off Below 1 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation) Below 1 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


a.

Disconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD


U190846C01
2.25,0.688 2.542,0.906 0.292,0.219 10 false N2 2.583,0.698 2.823,0.927 0.24,0.229 10 false *A 2.25,0.969 2.521,1.177 0.271,0.208 10 false O2 2.583,0.969 2.813,1.198 0.229,0.229 10 false *B
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
N2-2 (B) - Body ground W-B - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
O2-2 (B) - Body ground W-B - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-5 (LED) - N2-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N2-5 (LED) - N2-1 (GND) GR - W-B LED illumination signal Power switch off Below 1 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-5 (LED) - O2-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O2-5 (LED) - O2-1 (GND) GR - W-B LED illumination signal Power switch off Below 1 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


a.

Disconnect the Q4 power window regulator motor assembly (for rear LH door) connector.

U154588N01
2.375,0.823 2.677,1.115 0.302,0.292 10 false Q4


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
Q4-2 (B) - Body ground R - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the Q4 power window regulator motor assembly (for rear LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-5 (LED) - Q4-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
Q4-5 (LED) - Q4-1 (GND) Y - W-B LED illumination signal Power switch off Below 1 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


a.

Disconnect the P4 power window regulator motor assembly (for rear RH door) connector.

U154589N01
2.385,0.833 2.646,1.042 0.26,0.208 10 false P4


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
P4-2 (B) - Body ground R - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the P4 power window regulator motor assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-5 (LED) - P4-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
P4-5 (LED) - P4-1 (GND) GR - W-B LED illumination signal Power switch off Below 1 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB and L190 main body ECU (multiplex network body ECU) connectors.

U190882C02
0.708,2.771 1.031,2.771 true 3.156,7.583 3.448,7.75 0.292,0.167 10 false MB 4.875,6.385 5.167,6.552 0.292,0.167 10 false 2A 1.885,6.385 2.177,6.552 0.292,0.167 10 false 2B 1.177,5.115 1.469,5.281 0.292,0.167 10 false 2D 0.51,1.5 0.802,1.667 0.292,0.167 10 false 2D 3.917,5.135 4.208,5.302 0.292,0.167 10 false 2C 0.51,2.177 0.802,2.344 0.292,0.167 10 false 2C 4.792,3.802 5.302,3.969 0.51,0.167 10 false L201 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.583,5.104 5.875,5.271 0.292,0.167 10 false 2E 5.885,5.104 6.094,5.271 0.208,0.167 10 false *A 6.542,5.104 6.75,5.271 0.208,0.167 10 false *B 2.344,3.802 2.792,3.969 0.448,0.167 10 false L190 0.26,2.563 0.552,2.729 0.292,0.167 10 false 2E 0.573,2.552 0.865,2.719 0.292,0.167 10 false *A 0.583,2.854 0.875,3.021 0.292,0.167 10 false *B 0.281,2.854 0.573,3.021 0.292,0.167 10 false 2F 1.938,1.708 2.406,1.875 0.469,0.167 10 false L201 1.938,2.063 2.385,2.229 0.448,0.167 10 false L190 6.271,1.531 6.479,1.698 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.281,2.177 6.49,2.344 0.208,0.167 10 false 2A
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
L190-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V


c.

Reconnect the MB and L190 main body ECU (multiplex network body ECU) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2D-35 (FLCY) - Body ground Y*1 - Body ground
V*2 - Body ground
Front door courtesy switch LH input Front door LH open Below 1 V
2D-35 (FLCY) - Body ground Y*1 - Body ground
V*2 - Body ground
Front door courtesy switch LH input Front door LH closed 11 to 14 V
2D-36 (FRCY) - Body ground BR*1 - Body ground
V*2 - Body ground
Front door courtesy switch RH input Front door RH open Below 1 V
2D-36 (FRCY) - Body ground BR*1 - Body ground
V*2 - Body ground
Front door courtesy switch RH input Front door RH closed 11 to 14 V

*1: for LHD

*2: for RHD