Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301639 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

According to the display on the GTS, read the Data List.

Cruise Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cruise Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
Cruise Memory Vehicle Speed Stored vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Stored vehicle speed -
Cruise Request Throttle Opening Angle Cruise requested position 0 to 124.99° When cruise is set (vehicle in motion at 80 km/h (50 mph)): Actual requested throttle position -
Vehicle Acceleration Acceleration condition while driving the vehicle -13.1 to 13.1 m/s2 Current value displayed -
Cruise Target Acceleration Target acceleration while in cruise control mode -13.1 to 13.1 m/s2 Current value displayed -
Driving Support ECU Target Acceleration Target acceleration of driving support ECU -13.1 to 13.1 m/s2 - This item is displayed on the GTS but is not used.
Acceleration Continuation Decision Acceleration continuation decision condition ON or OFF - This item is displayed on the GTS but is not used.
Output Driving Force Generated drive torque -10.0 to 9.92 kN - This item is displayed on the GTS but is not used.
Cruise Request Driving Force Cruise request torque signal -10.0 to 9.92 kN Differs according to the cruise control system condition -
Cruise Request Driving Force Feedback Status Cruise request driving force feedback mode No Control, Suspend, Neg Calc Prohibited, Pos Calc Prohibited, Normal or Increasing at Start - This item is displayed on the GTS but is not used.
Cruise Control Permission Condition Cruise control system condition ON or OFF - This item is displayed on the GTS but is not used.
Cruise Control Condition Cruise control system active condition No Control or Constant Speed Control Mode - Ready - This item is displayed on the GTS but is not used.
Cruise Control Mode Cruise control mode condition No Control, Constant Speed Control Mode or Vehicle Distance Control Mode No Control: Cruise control not operating
Constant Speed Control Mode: Constant speed control mode operating
Vehicle Distance Control Mode: Vehicle distance control mode operating
-
Cruise Request Gear Position Shift request from power management control ECU None or 255 Gear Shift request from cruise control system -
Cruise Acceleration and Deceleration Operation Condition Cruise acceleration and deceleration operation condition No Control/Constant Speed Control Mode - Standby/Constant Speed Control Mode - RES SW Control/Constant Speed Control Mode - COAST SW Control/Vehicle Distance Control Mode - Acceleration Operation - This item is displayed on the GTS but is not used.
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON-OFF button) status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Accelerator Pedal Condition of the accelerator pedal during cruising ON or OFF ON: Accelerator pedal depressed
OFF: Accelerator pedal released
-
Stop Light Switch Sub-CPU Stop light switch signal ON or OFF - This item is displayed on the GTS but is not used.
Request Manual Cancel Whether there is a manual cancel request ON or OFF - This item is displayed on the GTS but is not used.
Request Automatic Cancel Whether there is an automatic cancel request ON or OFF - This item is displayed on the GTS but is not used.
Cruise Brake Control Decision Cruise brake control decision ON or OFF ON: Cruise brake activated
OFF: Cruise brake deactivated
-
Cruise Brake Control Permission Condition Cruise brake control permission condition OK or NG - This item is displayed on the GTS but is not used.
Cruise Indicator Cruise control indicator status ON or OFF ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off
-
Wheel Speed Sensor and Deceleration Sensor Speed sensor signal and deceleration sensor signal condition Avail or Not Avl Avail: Speed sensor signal and deceleration sensor signal available
Not Avl: Speed sensor signal and deceleration sensor signal not available
-
Gradient of Road Surface Gradient of road surface condition -32.76 to 32.76 m/s2 - This item is displayed on the GTS but is not used.



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the "Active Test".

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise control indicator light Cruise control indicator (illuminated in green) ON / OFF -
Indicat. SET Cruise control SET indicator light Cruise control SET indicator ON / OFF -
Cruise Indicator Cruise control indicator light Cruise control indicator (illuminated in amber) ON / OFF w/o multi-information display