When a signal is input from the P position switch (transmission shift main switch) or shift lever, the hybrid vehicle control ECU transmits a P position control (PCON) signal to the transmission control ECU assembly. Based on this signal, the transmission control ECU assembly actuates the shift control actuator assembly in order to mechanically lock or unlock the counter drive gear in the hybrid vehicle transaxle assembly.
P position state (engaged or released) of the actuator assembly is sent to the hybrid vehicle control ECU as a P position (PPOS) signal.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P085D | 582 | P position (PPOS) signal is logically inconsistent | ·
Wire harness or connector ·
Transmission control ECU assembly ·
Hybrid vehicle control ECU ·
Hybrid vehicle transaxle assembly |
| 599 | P position (PPOS) signal malfunction (output pulse is abnormal) | ·
Wire harness or connector ·
Transmission control ECU assembly ·
Hybrid vehicle control ECU |
|
| P0861 | 597 | GND short in P position (PPOS) signal circuit | ·
Wire harness or connector ·
Transmission control ECU assembly ·
Hybrid vehicle control ECU |
| P0862 | 598 | +B short in P position (PPOS) signal circuit | ·
Wire harness or connector ·
Transmission control ECU assembly ·
Hybrid vehicle control ECU |
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (IG) and wait for 10 seconds or more.
Depress the brake pedal, move the shift lever to N, and wait for 10 seconds or more.
Push the transmission shift main switch (P position switch) and wait for 10 seconds or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Chassis / Transmission Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| Electronic shift lever system DTCs are not output. | A |
| Any of the following DTCs are output. | B |
| DTC No. | Relevant Diagnosis |
|---|---|
| C2309 | Open in B+ Circuit |
| C2311 | Communication Error from HV ECU |
Turn the power switch off.
A
B
Disconnect the L5 hybrid vehicle control ECU connector.
Disconnect the A24 transmission control ECU assembly connector.
Disconnect the L197 certification ECU (smart key ECU assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
*b | Front view of wire harness connector
(to Transmission Control ECU Assembly) |
| *c | Front view of wire harness connector Certification ECU (Smart Key ECU Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-22 (PCON) - Body ground | Power switch on (IG) | Below 1 V |
| A24-23 (PPOS) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L5-8 (PCON) - A24-22 (PCON) | Power switch off | Below 1 Ω |
| L5-15 (PPOS) - A24-23 (PPOS) | Power switch off | Below 1 Ω |
| A24-23 (PPOS) - L197-25 (PPOS) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L5-8 (PCON) or A24-22 (PCON) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| L5-15 (PPOS), A24-23 (PPOS) or L197-25 (PPOS) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the L197 certification ECU (smart key ECU assembly) connector.
Reconnect the A24 transmission control ECU assembly connector.
Reconnect the L5 hybrid vehicle control ECU connector.
OK
NG
Turn the power switch on (IG).
Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.
| Item | Content |
|---|---|
| Terminal | L5-8 (PCON) - L5-6 (E1) |
| Equipment Setting | 10V/DIV., 10ms/DIV. |
| Condition | Power switch on (IG) |
| Result | Proceed to |
|---|---|
| P position control (PCON) signal waveform appears. | A |
| P position control (PCON) signal waveform does not appear. | B |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
Turn the power switch off.
A
B
Turn the power switch on (IG).
Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.
| Item | Content |
|---|---|
| Terminal | L5-15 (PPOS) - L5-6 (E1) |
| Equipment Setting | 10V/DIV., 10ms/DIV. |
| Condition | Power switch on (IG) |
| Result | Proceed to |
|---|---|
| P position (PPOS) signal waveform appears | A |
| P position (PPOS) signal waveform does not appear | B |
| *a | Component with harness connected
(Hybrid vehicle control ECU) |
Turn the power switch off.
A
B
Turn the power switch on (IG).
Depress the brake pedal and move the shift lever to select neutral (N).
Press the P position switch (transmission shift main switch) and check the status of the indicator light.
| Condition of Indicator Light | Proceed to |
|---|---|
| Other than below. | A |
| Indicator light flashes. | B |
Turn the power switch off.
A
B
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG) and leave the vehicle as it is for 10 seconds.
Depress the brake pedal, move the shift lever to N and leave the vehicle as it is for 10 seconds.
Push the P position switch (transmission shift main switch) and leave the vehicle as it is for 10 seconds.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| P085D-582, P085D-599, P0861-597 or P0862-598 is output again. | B |
Turn the power switch off.
A
B
Apply the parking brake.
Disconnect the shift control actuator assembly connector.
Remove the 3 shift control actuator bolts.
Click hereDrivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT CONTROL ACTUATOR>COMPONENTS
Slightly pull the shift control actuator assembly away from the hybrid vehicle transaxle.
| *a | Lock |
| *b | Unlock |
Wrap the shaft with a piece of cloth and check that it cannot be rotated in either direction by hand.
The shaft cannot be rotated by hand.
Do not use tools, such as pliers, to perform this step.
OK
NG