Home › Vehicle Interior › HEATING / AIR CONDITIONING › AMBIENT TEMPERATURE SENSOR › from 2017.12
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301848 AMBIENT TEMPERATURE SENSOR G

HEATING / AIR CONDITIONING  AMBIENT TEMPERATURE SENSOR  INSPECTION  


PROCEDURE

Hide 88790B 1.INSPECT AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)

a.
E293296C10
2.99,0.438 3.073,0.24 true 0.677,0.958 0.927,0.74 true 1.385,0.938 1.094,0.75 true 1.771,3.177 2.042,2.531 2.042,2.531 2.229,2.531 false 0.479,0.219 0.792,0.375 0.313,0.156 10 false *a 3.104,0.063 3.417,0.219 0.313,0.156 10 false *b 0.042,2.802 0.354,2.958 0.313,0.156 10 false *c 1.875,4.406 2.188,4.563 0.313,0.156 10 false *e 0.49,4.198 1.104,4.396 0.615,0.198 10 false (50) 1.042,4.208 1.656,4.406 0.615,0.198 10 false (68) 1.552,4.208 2.167,4.406 0.615,0.198 10 false (86) 2.073,4.208 2.688,4.406 0.615,0.198 10 false (104) 2.604,4.219 3.219,4.417 0.615,0.198 10 false (122) 3.083,4.219 3.427,4.438 0.344,0.219 10 false (140) 0.583,0.927 0.896,1.083 0.313,0.156 10 false - 1.448,0.917 1.76,1.073 0.313,0.156 10 false + 2.281,2.448 2.594,2.604 0.313,0.156 10 false *d
*a Component without harness connected
(ambient temperature sensor (thermistor assembly))
*b Sensing Portion
*c Resistance (kΩ)
*d Allowable Range
*e Temperature (°C (°F))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (-) 10 °C (50 °F) 3.00 to 3.73 kΩ
15 °C (59 °F) 2.45 to 2.88 kΩ
20 °C (68 °F) 1.95 to 2.30 kΩ
25 °C (77 °F) 1.60 to 1.80 kΩ
30 °C (86 °F) 1.28 to 1.47 kΩ
35 °C (95 °F) 1.00 to 1.22 kΩ
40 °C (104 °F) 0.80 to 1.00 kΩ
45 °C (113 °F) 0.65 to 0.85 kΩ
50 °C (122 °F) 0.50 to 0.70 kΩ
55 °C (131 °F) 0.44 to 0.60 kΩ
60 °C (140 °F) 0.36 to 0.50 kΩ


NOTICE:
·

Hold the sensor only by its connector. Touching the sensor may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).


If the result is not as specified, replace the ambient temperature sensor (thermistor assembly).