Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM D

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  OPERATION CHECK  


INPUT SIGNAL CHECK


A376504C03
1.958,0.094 2.271,0.292 0.313,0.198 10 false *a 1.833,1.958 2.146,2.156 0.313,0.198 10 false *b 3.083,1.646 3.396,1.844 0.313,0.198 10 false *c 0.385,1.573 0.698,1.771 0.313,0.198 10 false *d
*a +RES
*b -SET
*c ON-OFF
*d CANCEL


a.

Connect the GTS to the DLC3.


b.

Check the cruise control main switch using the Data List function of the GTS (ON-OFF, -SET, +RES and CANCEL).

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST



INSPECT CRUISE CONTROL MAIN SWITCH (ON-OFF BUTTON)


a.

Turn the power switch on (IG).


b.
A376503C04
3.073,1.667 3.385,1.865 0.313,0.198 10 false *a
*a ON-OFF


Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


c.
E301601C27
0.385,0.479 0.698,0.677 0.313,0.198 10 false *a 1.427,0.469 1.74,0.667 0.313,0.198 10 false *b
*a Cruise Control Indicator
(Vehicle-to-vehicle Distance Control Mode)
*b Multi-information Display


Check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter sub-assembly illuminates and "RADAR READY" is displayed on the multi-information display.


d.

Turn the cruise control system off using the cruise control main switch (ON-OFF button). Check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter sub-assembly and "RADAR READY" on the multi-information display turn off.


e.

Turn the power switch off with the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter sub-assembly illuminated and "RADAR READY" on the multi-information display displayed. Turn the power switch back on (IG) and check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter sub-assembly and "RADAR READY" on the multi-information display are turned off.



INSPECT MODE SELECT


a.

Turn the power switch on (IG).


b.
A376503C04
3.073,1.667 3.385,1.865 0.313,0.198 10 false *a
*a ON-OFF


Push and hold the switch of the cruise control main switch (ON-OFF button) for 1.5 seconds or more with the dynamic radar cruise control system off to change to the constant speed control mode.


c.
E301602C04
0.448,0.229 0.76,0.427 0.313,0.198 10 false *a 1.302,0.219 1.615,0.417 0.313,0.198 10 false *b 1.115,2.177 1.427,2.375 0.313,0.198 10 false *c
*a Cruise Control Indicator
(Vehicle-to-vehicle Distance Control Mode)
*b Multi-information Display
*c Cruise Control Indicator
(Constant Speed Control Mode)


Check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter sub-assembly and "RADAR READY" on the multi-information display turn off and the cruise control indicator (constant speed control mode) illuminates.

NOTICE:

Do not push any other switches before pushing the cruise control main switch to MODE. If any other switch is pushed, turn the dynamic radar cruise control system off and repeat the procedure above.


HINT:

If a malfunction is detected, turn the power switch off and repeat the procedure above.




INSPECT STEERING PAD SWITCH ASSEMBLY


a.

Turn the power switch on (IG).


b.
A376503C04
3.073,1.667 3.385,1.865 0.313,0.198 10 false *a
*a ON-OFF


Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


c.
A413074C02
2.594,1.354 3.01,1.594 false 3.052,1.51 3.281,1.688 0.229,0.177 10 false *a
*a Vehicle-to-vehicle Distance Control Switch


Press the steering pad switch assembly (vehicle-to-vehicle distance control switch).


d.

Check that the indicator of the vehicle-to-vehicle distance, which is shown on the multi-information display in the combination meter sub-assembly changes from long to middle to short in that order.

HINT:

Long is automatically selected each time the power switch is turned on (IG).