Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781N81
3.396,0.115 3.802,0.354 0.406,0.24 3.458,0.156 4.073,0.354 0.615,0.198 10 false L205

NOTICE:

Do not apply excessive force to the connector. If a force of 10 kg or more is applied, the connector may be broken.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L205-3 (BZ) - L205-28 (GND) L - W-B Skid control buzzer assembly output Power switch on (IG), buzzer not sounding 11 to 14 V
Power switch on (IG), buzzer sounding Below 1 V
L205-7 (B) - L205-28 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
L205-8 (CA1P) - L205-28 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L205-9 (CA1N) - L205-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
L205-10 (CA2H) - L205-28 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L205-11 (CA2L) - L205-28 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
L205-23 (SPSW) - L205-28 (GND) R - W-B Steering pad switch assembly signal (distance control signal) Power switch on (IG), steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
Power switch on (IG), steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
L205-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between L205-8 (CA1P) and L205-28 (GND)

·

Between L205-10 (CA2H) and L205-28 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between L205-9 (CA1N) and L205-28 (GND)

·

Between L205-11 (CA2L) and L205-28 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK HYBRID VEHICLE CONTROL ECU


B344905N34
1.344,0.094 1.729,0.313 0.385,0.219 2.781,0.094 3.167,0.313 0.385,0.219 4.208,0.094 4.594,0.313 0.385,0.219 5.469,0.094 5.854,0.313 0.385,0.219 1.417,0.135 1.875,0.333 0.458,0.198 10 false A21 2.865,0.135 3.323,0.333 0.458,0.198 10 false A22 4.323,0.125 4.74,0.344 0.417,0.219 10 false L5 5.583,0.125 5.979,0.323 0.396,0.198 10 false L6

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A21-15 (STP) - L5-6 (E1) L - W-B Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
L5-24 (VSX1) - L5-23 (E2X1) L - SB Shift sensor (Main) Power switch on (IG), shift lever in home position or N 2.0 to 3.0 V
Power switch on (IG), shift lever in R 0.3 to 1.8 V
Power switch on (IG), shift lever in B or D 3.2 to 4.8 V
L5-21 (VSX2) - L5-22 (E2X2) LG - V Shift sensor (Sub) Power switch on (IG), shift lever in home position or N 2.0 to 3.0 V
Power switch on (IG), shift lever in R 0.3 to 1.8 V
Power switch on (IG), shift lever in B or D 3.2 to 4.8 V
A22-28 (ST1-) - L5-6 (E1) R - W-B Stop light switch signal Power switch on (IG), brake pedal depressed Below 1 V
Power switch on (IG), brake pedal released 11 to 14 V
L5-28 (CCS) - L5-6 (E1) BE - W-B Cruise control main switch circuit Cruise control main switch (ON-OFF button) not pushed 1 MΩ or higher
Cruise control main switch (ON-OFF button) pushed Below 2.5 Ω
+RES switch ON 235 to 245 Ω
-SET switch ON 617 to 643 Ω
CANCEL switch ON 1509 to 1571 Ω


CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


E321782N64
2.167,0.75 2.583,1 0.417,0.25 2.26,0.802 2.719,1 0.458,0.198 10 false A91

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A91-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A91-2 (CA2L) - A91-1 (SGND) BR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A91-3 (CA2H) - A91-1 (SGND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A91-5 (CA1P) - A91-1 (SGND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A91-6 (CA1N) - A91-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A91-8 (IGB) - A91-1 (SGND) R - W-B Power source Power switch on (IG) 11 to 14 V

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between A91-3 (CA2H) and A91-1 (SGND)

·

Between A91-5 (CA1P) and A91-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between A91-2 (CA2L) and A91-1 (SGND)

·

Between A91-6 (CA1N) and A91-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.