Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061945 SEAT BELT _0301836 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Disconnect the main body ECU (multiplex network body ECU) connectors.

U190880C01
1.76,0.677 1.615,0.677 1.615,0.677 1.615,0.958 false 4.156,0.823 4.01,0.823 4.01,0.823 4.01,1.115 false 1.573,1.698 1.479,1.698 false 1.979,1.698 1.677,1.698 false 1.979,2.052 1.677,2.052 false 1.573,2.052 1.479,2.052 false 0.719,2.708 1.042,2.708 false 3.135,7.594 3.427,7.76 0.292,0.167 10 false MB 4.865,6.385 5.156,6.552 0.292,0.167 10 false 2A 1.865,6.385 2.156,6.552 0.292,0.167 10 false 2B 1.156,5.115 1.448,5.281 0.292,0.167 10 false 2D 0.906,1.51 1.208,1.74 0.302,0.229 10 false 2D 3.927,5.146 4.219,5.313 0.292,0.167 10 false 2C 0.906,2.125 1.219,2.344 0.313,0.219 10 false 2C 4.781,3.802 5.167,3.969 0.385,0.167 10 false L201 6.25,5.115 6.542,5.281 0.292,0.167 10 false 2F 5.583,5.115 5.875,5.281 0.292,0.167 10 false 2E 5.896,5.104 6.104,5.271 0.208,0.167 10 false *A 6.552,5.115 6.76,5.281 0.208,0.167 10 false *B 2.333,3.802 2.708,3.969 0.375,0.167 10 false L190 0.365,2.635 0.75,2.823 0.385,0.188 10 false 2E*A 0.365,2.823 0.781,3.094 0.417,0.271 10 false 2F*B 2.01,1.625 2.385,1.802 0.375,0.177 10 false L201 2.01,1.969 2.448,2.135 0.438,0.167 10 false L190 5.854,1.458 6.167,1.719 0.313,0.26 10 false 2B 4.198,0.698 4.5,0.906 0.302,0.208 10 false MB 5.854,2.125 6.146,2.333 0.292,0.208 10 false 2A 1.823,0.604 2.104,0.844 0.281,0.24 10 false *1
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) - -



b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-31 (ALTB) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Power switch on (IG) → off 11 to 14 V → Below 1 V
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Power switch on (ACC) → off 11 to 14 V → Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-18 (DBKL) - Body ground - Driver seat belt buckle switch signal Driver seat belt fastened 10 kΩ or higher
Driver seat belt unfastened Below 1 Ω
L201-6 (LRCY) - Body ground G - Body ground Rear door courtesy light switch LH or RH input Rear door LH or RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK COMBINATION METER SUB-ASSEMBLY


a.

Disconnect the L27 combination meter sub-assembly connector.

U190795E02
3.49,0.104 3.76,0.25 0.271,0.146 10 false L27


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
L27-11 (ES) - Body ground BR - Body ground Ground Always Below 1 Ω
L27-29 (SW) - Body ground R - Body ground Front passenger seat belt buckle switch signal Front passenger seat occupied, seat belt fastened 10 kΩ or higher
Front passenger seat occupied, seat belt unfastened Below 1 Ω
L27-38 (RLSB) - Body ground SB - Body ground Rear No. 1 seat belt LH buckle switch signal Rear No. 1 seat belt LH fastened 10 kΩ or higher
Rear No. 1 seat belt LH unfastened Below 1 Ω
L27-37 (RCSB) - Body ground L - Body ground Rear No. 1 seat belt center buckle switch signal Rear No. 1 seat belt center fastened 10 kΩ or higher
Rear No. 1 seat belt center unfastened Below 1 Ω
L27-36 (RRSB) - Body ground R - Body ground Rear No. 1 seat belt RH buckle switch signal Rear No. 1 seat belt RH fastened 10 kΩ or higher
Rear No. 1 seat belt RH unfastened Below 1 Ω
L27-40 (RLBT) - Body ground W - Body ground Rear No. 2 seat belt LH buckle switch signal Rear No. 2 seat belt LH fastened 10 kΩ or higher
Rear No. 2 seat belt LH unfastened Below 1 Ω
L27-39 (RRBT) - Body ground B - Body ground Rear No. 2 seat belt RH buckle switch signal Rear No. 2 seat belt RH fastened 10 kΩ or higher
Rear No. 2 seat belt RH unfastened Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the L27 combination meter sub-assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
L27-1 (B) - Body ground L - Body ground Battery power supply Power switch off 11 to 14 V
L27-2 (IG+) - Body ground BR - Body ground Ignition power supply
(IG signal)
Power switch off Below 1 V
Power switch on (IG) 11 to 14 V

If the result is not as specified, the combination meter sub-assembly may have a malfunction.