DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Warm up the engine.
Turn the A/C switch off.
Turn the power switch off.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Ptrl General / -
Ptrl AF Control / Air fuel ratio control system related data
Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
Ptrl Throttle / Gasoline throttle system related data
Ptrl Intake Control / Intake control system related data
Ptrl Valve Control / Valve control system related data
Ptrl Misfire / "Misfire" related data
Ptrl Starting / "Difficult to start" related data
Ptrl Rough Idle / "Rough idle" related data
Ptrl Evaporative / Evaporative system related data
Ptrl CAT Converter / Catalyst converter related data
Check Mode / Check mode related data
Monitor Status / Monitor status related data
Ignition / Ignition system related data
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transaxle system related data
Vehicle Information / Vehicle information
According to the display on the GTS, read the Data List.
The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.
Various Vehicle Conditions 1 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Actual vehicle speed | Yes |
| Diagnostic Note:
This is the current vehicle speed |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed | Engine speed/
Min.: 0 rpm, Max.: 16383 rpm |
950 to 1050 rpm: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | Yes |
| Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Calculate Load | Load calculated by ECM/
Min.: 0%, Max.: 100% |
·
20 to 40%: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) ·
15 to 35%: Running without load (2500 rpm) |
Yes |
| Diagnostic Note:
This is the engine load calculated based on the actual intake manifold pressure. Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the actual intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Vehicle Load | Vehicle load/
Min.: 0%, Max.: 25700% |
Actual vehicle load | Yes |
| Diagnostic Note:
This is the engine intake air charging efficiency. Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow x 100% Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MAF | Airflow rate from mass air flow meter sub-assembly/
Min.: 0 gm/sec, Max.: 655.35 gm/sec |
1 to 3 gm/sec: Idling with warmed up engine (inspection mode [maintenance mode], not charge control)
4.5 to 8.5 gm/sec: Warmed up engine, 2500 rpm (inspection mode [maintenance mode]) |
Yes |
| Diagnostic Note:
This is the intake air amount from the mass air flow meter sub-assembly. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Atmosphere Pressure | Atmospheric pressure/
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1913 mmHg) |
Equivalent to atmospheric pressure (absolute pressure) | Yes |
| Diagnostic Note:
·
This value is calculated from the intake air amount. ·
Standard atmospheric pressure: 101 kPa(abs) [758 mmHg(abs)] ·
For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies depending on the weather. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MAP | Intake manifold absolute pressure/
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1913 mmHg) |
·
80 to 110 kPa(abs) [600 to 825 mmHg(abs)]: Power switch on (IG) ·
20 to 40 kPa(abs) [150 to 300 mmHg(abs)]: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) |
Yes |
| Diagnostic Note:
·
This is the intake manifold pressure. ·
This item is the pressure detected by the manifold absolute pressure sensor and is used for air fuel ratio control and EGR valve control.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | Yes |
| Diagnostic Note:
This is the engine coolant temperature.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Intake Air | Intake air temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F) |
Equivalent to temperature at location of mass air flow meter sub-assembly | Yes |
| Diagnostic Note:
This is the engine intake air temperature.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Ambient Temperature | Ambient temperature/
Min.: -40°C (-40°F), Max.: 215°C (419°F) |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Run Time | Engine run time/
Min.: 0 s (seconds), Max.: 65535 s (seconds) |
Time after power switch on (READY) | Yes |
| Diagnostic Note:
·
This is the time elapsed since the engine is first started with the power switch on (READY). ·
With the power switch on (READY), time measurement will not stop even after the engine stops. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Initial Engine Coolant Temp | Engine coolant temperature when the power switch is turned on (READY)/
Min.: -40°C (-40°F), Max.: 119.3°C (247°F) |
- | Yes |
| Diagnostic Note:
This is the engine coolant temperature stored when the power switch is turned on (READY). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Initial Intake Air Temp | Initial intake air temperature when the power switch is turned on (READY)/
Min.: -40°C (-40°F), Max.: 119.3°C (247°F) |
- | Yes |
| Diagnostic Note:
This is the intake air temperature stored when the power switch is turned on (IG). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Battery Voltage | Auxiliary battery voltage/
Min.: 0 V, Max.: 65.535 V |
11 to 16 V: Power switch on (IG) | Yes |
| Diagnostic Note:
If 11 V or less, characteristics of some electrical components may change. |
|||
Throttle Control (Ptrl Throttle)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sensor Volt % | Absolute No. 1 throttle position sensor/
Min.: 0%, Max.: 100% |
10 to 22%: Power switch on (IG), accelerator pedal fully released | Yes |
| Diagnostic Note:
The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttl Sensor #2 Volt % | Absolute No. 2 throttle position sensor/
Min.: 0%, Max.: 100% |
42 to 62%: Power switch on (IG), accelerator pedal fully released | Yes |
| Diagnostic Note:
The No. 2 throttle position sensor output is converted using 5 V = 100%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| System Guard | System guard/
ON or OFF |
ON: Idling or throttle actuator operating | No |
| Diagnostic Note:
When there is a difference between the target and actual throttle valve opening angle, this item changes to OFF and the electronic throttle control system operation is disabled. OFF: Electronic throttle control is stopped. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Idle Position | Whether or not throttle position sensor detecting idle/
ON or OFF |
- | No |
| Diagnostic Note:
This is a parameter calculated by the ECM. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Require Position | Required throttle position/
Min.: 0 V, Max.: 4.98 V |
0.5 to 1.1 V: Idling with warmed up engine (inspection mode [maintenance mode]) | No |
| Diagnostic Note:
This is a value calculated by the ECM showing the voltage for the target throttle valve position. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sensor Position | Throttle sensor position/
Min.: 0%, Max.: 100% |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position No. 1 | No. 1 throttle position sensor output voltage/
Min.: 0 V, Max.: 4.98 V |
·
0.5 to 1.1 V: Power switch on (IG), accelerator pedal fully released ·
0.6 to 1.4 V: Fail-safe operating |
No |
| Diagnostic Note:
This is the No. 1 throttle position sensor output voltage. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position No. 2 | No. 2 throttle position sensor output voltage/
Min.: 0 V, Max.: 4.98 V |
·
2.1 to 3.1 V: Power switch on (IG), accelerator pedal fully released ·
2.1 to 3.1 V: Fail-safe operating |
No |
| Diagnostic Note:
This is the No. 2 throttle position sensor output voltage. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Position Command | Throttle position command value/
Min.: 0 V, Max.: 4.98 V |
- | No |
| Diagnostic Note:
Throttle Position Command is the same value as Throttle Require Position. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sens Open Pos #1 | No. 1 throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V |
0.6 to 1.4 V | No |
| Diagnostic Note:
This is the No. 1 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the power switch on (IG). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sens Open Pos #2 | No. 2 throttle position sensor /
Min.: 0 V, Max.: 4.98 V |
1.7 to 2.5 V | No |
| Diagnostic Note:
This is the No. 2 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the power switch on (IG). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor Current | Throttle motor current/
Min.: 0 A, Max.: 19.9 A |
0 to 3.0 A: Idling with warmed up engine (inspection mode [maintenance mode], A/C off selected) | No |
| Diagnostic Note:
When this value is large but the actual opening angle (Throttle Position No. 1) does not reach the target opening angle (Throttle Require Position), there is an unable to open malfunction. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor DUTY | Throttle actuator/
Min.: 0%, Max.: 100% |
10 to 22%: Idling with warmed up engine (inspection mode [maintenance mode], A/C off selected) | Yes |
| Diagnostic Note:
This is the output duty ratio of the throttle actuator drive circuit. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255% |
0 to 40%: Idling with warmed up engine (inspection mode [maintenance mode], A/C off selected) | No |
| Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255% |
0 to 40%: Idling with warmed up engine (inspection mode [maintenance mode], A/C off selected) | No |
| Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Fully Close Learn | Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V |
0.4 to 1.0 V: Power switch on (IG), accelerator pedal fully released | No |
| Diagnostic Note:
·
The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle (approximately 5.5°, the position when the power switch is on (IG), the accelerator pedal is released and the throttle actuator is off). ·
Learning is performed immediately after the power switch is turned on (IG). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| +BM Voltage | +BM voltage/
Min.: 0 V, Max.: 79.998 V |
11 to 16 V: Power switch on (IG) and system normal | No |
| Diagnostic Note:
This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the power switch is turned off). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Actuator Power Supply | Actuator power supply/
ON or OFF |
ON: Engine running or throttle actuator operating | No |
| Diagnostic Note:
If +BM power is lost, this item changes to OFF. |
|||
Fuel System (Ptrl General)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injector (Port) | Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs |
1000 to 3000 μs: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | Yes |
| Diagnostic Note:
This is the injection period of the No. 1 cylinder (the command value from the ECM). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Volum (Cylinder 1) | Injection volume (Cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml |
0.03 to 0.13 ml: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | Yes |
| Diagnostic Note:
This is the fuel injection volume for 10 injections. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Pump/Speed Status | Fuel pump status/
ON or OFF |
ON: Engine running | Yes |
Fuel System 2 (Ptrl General)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Current Fuel Type | Current fuel type | Gasoline/petrol | Yes |
EVAP System (Ptrl Evaporative)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| EVAP (Purge) VSV | Purge VSV control duty/
Min.: 0%, Max.: 100% |
0 to 50%: Idling, under purge control | Yes |
| Diagnostic Note:
·
This is the command signal from the ECM. ·
This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed. *: Fuel vapor from the fuel tank is being introduced into the intake system via the purge VSV. ·
When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV is 0%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Evap Purge Flow | Purge flow/
Min.: 0%, Max.: 399.9% |
0 to 10%: Idling | Yes |
| Diagnostic Note:
This is the percentage of total engine airflow contributed by EVAP purge operation. (Evap Purge Flow = Purge flow / Engine airflow x 100 (%)) It is based on MAF and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Purge Density Learn Value | Purge density learned value/
Min.: -200, Max.: 199.993 |
-40 to 10: Idling | Yes |
| Diagnostic Note:
Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate. When Purge Density Learn Value is a large negative value, the purge effect is large. The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced. Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| EVAP Purge VSV | VSV status for EVAP control/
ON or OFF |
- | Yes |
| Diagnostic Note:
This parameter displays ON when EVAP (Purge) VSV is approximately 30% or more, and displays OFF when the VSV duty ratio is less than 30%. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Purge Cut VSV Duty | Purge VSV duty/
Min.: 0%, Max.: 399.9% |
- | Yes |
Air Fuel Ratio Control (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Air-Fuel Ratio | Target air fuel ratio/
Min.: 0, Max.: 1.999 |
0.8 to 1.2: Idling with warmed up engine (inspection mode [maintenance mode]) | Yes |
| Diagnostic Note:
This is the target air fuel ratio used by the ECM. 1.0 is the stoichiometric air fuel ratio. Values that are more than 1 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1 indicate the system attempting to make the air fuel ratio richer. Target Air-Fuel Ratio and AF Lambda B1S1 are related. |
|||
Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| AF Lambda B1S1 | Output air fuel ratio associated with bank 1 sensor 1/
Min.: 0, Max.: 1.999 |
·
Value less than 1 (0.000 to 0.999) = Rich ·
1 = Stoichiometric air fuel ratio ·
Value more than 1 (1.001 to 1.999) = Lean |
Yes |
| Diagnostic Note:
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.999 V |
2.6 to 3.8 V: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | Yes |
| Diagnostic Note:
This is the output voltage of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current B1S1 below for the actual sensor output). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| AFS Current B1S1 | Air fuel ratio sensor output current for bank 1 sensor 1/
Min.: -128 mA, Max.: 127.99 mA |
-0.5 to 0.5 mA: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | Yes |
| Diagnostic Note:
·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA. ·
When the value is outside the range of 0.7 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Heater Duty B1S1 | Air fuel ratio sensor heater duty ratio for bank 1 sensor 1/
Min.: 0%, Max.: 399.9% |
0 to 100% | Yes |
| Diagnostic Note:
When the value is any value except 0%, current is being supplied to the heater. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2S B1S2 | Heated oxygen sensor output voltage for bank 1 sensor 2/
Min.: 0 V, Max.: 1.275 V |
0.0 to 0.9 V | Yes |
| Diagnostic Note:
This is the output voltage of the heated oxygen sensor. Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio. Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio. During air fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2 Heater B1S2 | Heated oxygen sensor heater for bank 1 sensor 2/
Not Act or Active |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current for bank 1 sensor 2/
Min.: 0 A, Max.: 4.999 A |
- | Yes |
| Diagnostic Note:
When the value is any value except 0 A, current is being supplied to the heater. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Short FT B1S1 | Short-term fuel trim for bank 1/
Min.: -100%, Max.: 99.2% |
-20 to 20% | Yes |
| Diagnostic Note:
This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Long FT B1S1 | Long-term fuel trim for bank 1/
Min.: -100%, Max.: 99.2% |
-20 to 20% | Yes |
| Diagnostic Note:
The ECM will learn the Long FT B1S1 values based on Short FT B1S1. The goal is to keep Short FT B1S1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio. This value is used to determine whether the system related to air fuel ratio control is malfunctioning. The condition of the system is determined based on the sum of Short FT B1S1 and Long FT B1S1 (excluding times when the system is in transition). ·
20% or higher: There may be a lean air fuel ratio. ·
-20 to 20%: The air fuel ratio can be determined to be normal. ·
-20% or less: There may be a rich air fuel ratio. ·
Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT B1S1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT B1S1" indicates the current engine operating range. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Idle #1 | Idle area of air fuel ratio learn value/
Min.: -50%, Max.: 49.6% |
-20 to 20% | Yes |
| Diagnostic Note:
Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Low #1 | Low load area of air fuel ratio learn value/
Min.: -50%, Max.: 49.6% |
-20 to 20% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Mid1 #1 | Middle 1 load area of air fuel ratio learn value/
Min.: -50%, Max.: 49.6% |
-20 to 20% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value Mid2 #1 | Middle 2 load area of air fuel ratio learn value/
Min.: -50%, Max.: 49.6% |
-20 to 20% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/F Learn Value High #1 | High load area of air fuel ratio learn value/
Min.: -50%, Max.: 49.6% |
-20 to 20% | Yes |
| Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Total FT #1 | Total fuel trim for bank 1 (Average value for fuel trim system of bank 1)/
Min.: -0.5, Max.: 0.496 |
-0.28 to 0.2: Idling with warmed up engine (inspection mode [maintenance mode]) | Yes |
| Diagnostic Note:
Total FT #1 = Short FT B1S1 + Long FT B1S1 |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel System Status #1 | Fuel system status for bank 1/
OL, CL, OLDrive, OLFault, CLFault or Unused |
CL: Idling with warmed up engine (inspection mode [maintenance mode]) | Yes |
| Diagnostic Note:
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop. ·
CL (Closed Loop): Feedback for fuel control. ·
OLDrive: Open loop due to driving conditions (fuel enrichment). ·
OLFault: Open loop due to a detected system fault. ·
CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel System Status #2 | Fuel system status for bank 2/
OL, CL, OLDrive, OLFault, CLFault or Unused |
Unused | Yes |
Ignition System (Ignition)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| IGN Advance | Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg. |
0 to 16 deg.: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Knock Feedback Value | Knocking feedback value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) |
-20 to 0 deg(CA)
Driving at 70 km/h (43 mph) |
Yes |
| Diagnostic Note:
This is the ignition timing retard compensation amount determined by the presence or absence of knocking. Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount Example: 21 deg(CA) = 10 deg(CA) + 14 deg(CA) - 3 deg(CA) *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3 deg(CA) as possible. When Knock Feedback Value is less than -4 deg (CA), Knock Correct Learn Value is slowly decreased. When Knock Feedback Value is more than -2 deg(CA), Knock Correct Learn Value is slowly increased. *3: The base value is -3 deg(CA) and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased. -1 deg(CA): There is no knocking and ignition timing is advanced. -6 deg(CA): Knocking is present and the ignition timing is being retarded.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Knock Correct Learn Value | Knocking correction learned value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) |
0 to 22 deg(CA)
Driving at 70 km/h (43 mph) |
Yes |
| Diagnostic Note:
Refer to "Knock Feedback Value". When there is knocking or a lack of power, compare the following values to another vehicle of the same model. ·
Engine Speed ·
Calculate Load ·
IGN Advance ·
Knock Feedback Value ·
Knock Correct Learn Value Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced. Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.
|
|||
EGR System (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target EGR Position | EGR valve target opening amount/
Min.: 0%, Max.: 100% |
0%: Idling with warmed up engine (inspection mode [maintenance mode]) | Yes |
| Diagnostic Note:
When the engine is cold or idling, at engine start, etc., the value is 0%. When the valve is fully closed, the value is 0%. When the valve is fully open, the value is 100%.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| EGR Step Position | EGR step position/
Min.: 0 step, Max.: 255 step |
0 step: Idling with warmed up engine (inspection mode [maintenance mode]) | Yes |
| Diagnostic Note:
This is the ECM control command. When the valve is fully closed, the value is 0 step. When the valve is fully open, the value is 110 step. |
|||
VVT Control 2 (Ptrl Valve Control)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Control Status #1 | Variable valve timing (VVT) control status for bank 1/
ON or OFF |
- | Yes |
| Diagnostic Note:
ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF). OFF: The system is commanding the timing to change to the most retarded timing. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Aim Angle #1 | VVT hold duty learned value for bank 1/
Min.: 0%, Max.: 399.9% |
- | No |
| Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced state of the VVT controller. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Change Angle #1 | VVT displacement angle for bank 1/
Min.: 0 DegFR, Max.: 639.9 DegFR |
- | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT OCV Duty #1 | Camshaft timing oil control valve assembly operation duty for bank 1/
Min.: 0%, Max.: 399.9% |
- | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VVT Target Angle #1 | VVT target angle for bank 1/
Min.: 0 DegFR, Max.: 639.9 DegFR |
- | No |
Various Vehicle Conditions 2 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VN Turbo Type | Variable nozzle turbo type/
Not Avl, Commo, Vacuum, CAN Com or DC |
Not Avl (Unused) | No |
Catalyst (Ptrl CAT Converter)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Catalyst Temp B1S1 | Catalyst temperature for bank 1 sensor 1/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) |
- | Yes |
| Diagnostic Note:
This is the temperature of the front catalyst estimated by the ECM. This value is included in the conditions used to detect catalyst deterioration (DTC P0420), etc., and should therefore be used as a reference when recreating malfunction conditions. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Catalyst Temp B1S2 | Catalyst temperature for bank 1 sensor 2/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) |
- | Yes |
| Diagnostic Note:
This is the temperature of the rear catalyst estimated by the ECM. |
|||
Various Vehicle Conditions 3 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Closed Throttle Position SW | Closed throttle position switch/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Cut Condition | Fuel cut condition/
ON or OFF |
ON: Fuel cut operating or engine stopped | Yes |
Test Result (Monitor Status)
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note | Stored as Freeze Frame Data |
|---|---|---|---|---|
| Complete Parts Monitor | Comprehensive component monitor/
Not Avl or Avail |
- | *1 | No |
| Fuel System Monitor | Fuel system monitor/
Not Avl or Avail |
- | *1 | No |
| Misfire Monitor | Misfire monitor/
Not Avl or Avail |
- | *1 | No |
| EGR/VVT Monitor | EGR/VVT monitor/
Not Avl or Avail |
- | *1 | No |
| EGR/VVT Monitor | EGR/VVT monitor/
Compl or Incmpl |
- | *1 | No |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/
Not Avl or Avail |
- | *1 | No |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/
Compl or Incmpl |
- | *1 | No |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/
Not Avl or Avail |
- | *1 | No |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/
Compl or Incmpl |
- | *1 | No |
| A/C Monitor | A/C monitor/
Not Avl or Avail |
- | *1 | No |
| A/C Monitor | A/C monitor/
Compl or Incmpl |
- | *1 | No |
| 2nd Air Monitor | 2nd air monitor/
Not Avl or Avail |
- | *1 | No |
| 2nd Air Monitor | 2nd air monitor/
Compl or Incmpl |
- | *1 | No |
| EVAP Monitor | EVAP monitor/
Not Avl or Avail |
- | *1 | No |
| EVAP Monitor | EVAP monitor/
Compl or Incmpl |
- | *1 | No |
| Heated Catalyst Monitor | Heated catalyst monitor/
Not Avl or Avail |
- | *1 | No |
| Heated Catalyst Monitor | Heated catalyst monitor/
Compl or Incmpl |
- | *1 | No |
| Catalyst Monitor | Catalyst monitor/
Not Avl or Avail |
- | *1 | No |
| Catalyst Monitor | Catalyst monitor/
Compl or Incmpl |
- | *1 | No |
| *1:
Avail: The monitor is available on the vehicle. Not Avl: The monitor is not available on the vehicle. Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the power switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the auxiliary battery cable is disconnected. |
||||
Various Vehicle Conditions 4 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| TC Terminal | TC terminal status/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| # Codes (Include History) | Number of codes/
Min.: 0, Max.: 255 |
0 | No |
| Diagnostic Note:
This is the number of DTCs stored. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MIL | MIL status/
ON or OFF |
OFF | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MIL ON Run Distance | Distance driven with MIL on/
Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile) |
- | No |
| Diagnostic Note:
This is the distance driven since the MIL was illuminated. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Running Time from MIL ON | Running time from MIL ON/
Min.: 0 min, Max.: 65535 min |
Running time after MIL turned on | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Time after DTC Cleared | Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min |
Time after DTCs cleared | Yes |
| Diagnostic Note:
This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the power switch is turned off is not counted. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Distance from DTC Cleared | Distance driven after DTCs cleared/
Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) |
Equivalent to driven distance after DTCs cleared | Yes |
| Diagnostic Note:
This is the distance driven after DTCs were cleared (or after the vehicle left the factory). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255 |
- | Yes |
| Diagnostic Note:
This is the number of warmup cycles after the DTCs were cleared. This is the number of times the engine was warmed up after DTCs were cleared (or after the vehicle left the factory). |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Dist Batt Cable Disconnect | Distance driven after auxiliary battery cable disconnected/
Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile) |
Total distance vehicle driven after auxiliary battery cable disconnected | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| IG OFF Elapsed Time | Time after power switch off/
Min.: 0 min, Max.: 655350 min |
Cumulative time after power switch off | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| OBD Requirements | OBD requirement | E-OBD | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Number of Emission DTC | Emission related DTCs | - | No |
| Diagnostic Note:
This is the number of emissions-related DTCs. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| TC and TE1 | TC and CG (TE1) terminals of DLC3/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Total Distance Traveled | Total distance traveled/
Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) |
- | Yes |
Misfire (Ptrl Misfire)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Ignition Trig. Count | Ignition counter/
Min.: 0, Max.: 65535 |
0 to 400 | Yes |
| Diagnostic Note:
This is the cumulative number of ignitions. This counter is incremented by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions. The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by Ignition Trig. Count. The misfire rate for each cylinder = Cylinder #1 to #4 Misfire Count / Ignition Trig. Count
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Cylinder #1 Misfire Count
Cylinder #2 Misfire Count Cylinder #3 Misfire Count Cylinder #4 Misfire Count |
Misfire count of cylinders 1 to 4/
Min.: 0, Max.: 255 |
0 | Yes |
| Diagnostic Note:
This is the misfire count for each individual cylinder. This counter is incremented by one for each misfire and is cleared every 200 revolutions. Check this item to help determine the malfunctioning cylinder. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| All Cylinders Misfire Count | Misfire count of all cylinders/
Min.: 0, Max.: 255 |
0 | Yes |
| Diagnostic Note:
This is the total misfire count of all cylinders. This counter is incremented by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Misfire RPM | Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm |
0 rpm: 0 misfire | Yes |
| Diagnostic Note:
·
This is the average engine speed recorded when misfiring occurs. ·
This value is closer to the actual conditions of the vehicle at the time the misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Misfire Load | Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev |
0 g/rev: 0 misfire | Yes |
| Diagnostic Note:
·
This is the average engine load recorded when misfiring occurs. ·
This value is closer to the actual conditions of the vehicle at the time the misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Misfire Margin | Misfire monitoring/
Min.: -128%, Max.: 127% |
0 to 127%: Idling | Yes |
| Diagnostic Note:
This is the misfire detection margin. Misfire Margin = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100% When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. Misfire margin is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring. A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring. Example: When the engine is determined to be misfiring, Misfire Margin = -128 to 0%. |
|||
Various Vehicle Conditions 5 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of IG Switch | Power switch condition/
ON or OFF |
ON: Power switch on (IG) | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of Ready | Power switch condition/
ON or OFF |
ON: Power switch on (READY) | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of Engine Start | Engine start condition/
ON or OFF |
ON: Engine running | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of WI Terminal Low Voltage Guard Determination | WI low voltage guard judgment/
ON or OFF |
OFF | Yes |
| Diagnostic Note:
In order to prevent data corruption due to low voltage while writing to RAM, if the VC voltage drops to 4.5 V or less, this item is set to "ON" to prohibit writing to RAM. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of +B Terminal Low Voltage Guard Determination | +B low voltage guard judgment/
ON or OFF |
OFF | Yes |
| Diagnostic Note:
When the system is unstable due to low auxiliary battery voltage, DTCs cannot be accurately detected. Therefore, when the +B voltage drops to 7.5 V or less, this item is set to "ON" to prohibit DTC detection. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of STA Terminal Low Voltage Guard Determination | STA low voltage guard judgment/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of IG Switch Terminal Low Voltage Guard Determination | IGSW low voltage guard judgment/
ON or OFF |
- | Yes |
| Diagnostic Note:
When other ECUs do not start while the power switch is off or the system is unstable immediately after the ECM starts, DTCs cannot be accurately detected. Therefore, the power switch is turned off or 0.5 seconds after the power switch is turned on (IG), this item is set to "ON" to prohibit DTC detection. |
|||
Soak Timer (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Status of Soak Timer Start | Soak timer start condition/
ON or OFF |
ON: Soak timer starting | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Soak Timer Start Request | Start signal from soak timer IC/
ON or OFF |
ON: Soak timer starting | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Soak IC Current Timer Value | Current soak timer value/
Min.: 0 sec, Max.: 614390.625 sec |
- | Yes |
| Diagnostic Note:
P2610 clock comparison detection compares "Soak IC Current Timer Value" and "Soak Timer Clear" to detect malfunctions. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Soak Timer Clear | Time elapsed since soak timer was cleared/
Min.: 0 ms, Max.: 4294901.76 ms |
- | Yes |
| Diagnostic Note:
When the power switch is turned off after the engine starts, the "Soak Timer Clear" value is cleared. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Soak Timer Start History | Soak timer start history/
ON, OFF or Unknown |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Soak IC First Start Time | Initial soak timer start time/
Min.: 0 min, Max.: 2550 min |
- | Yes |
| Diagnostic Note:
First time soak timer started after power switch was turned off. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Soak Start Count | Number of times soak timer started from power switch on (IG) to power switch off/
Min.: 0, Max.: 255 |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Main Relay ON Time after IG OFF | EFI MAIN relay ON time after power switch was turned off/
Min.: 0 ms, Max.: 4294901.76 ms |
- | Yes |
| Diagnostic Note:
When the power switch is on (IG), this item displays 0 ms. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Main Relay ON Time after IG OFF of Previous Trip | EFI MAIN relay ON time after previous time power switch was turned off/
Min.: 0 ms, Max.: 4294901.76 ms |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Main Relay ON Time after Soak Start of Previous Trip | EFI MAIN relay ON time after previous clock comparison detection/
Min.: 0 ms, Max.: 4294901.76 ms |
- | Yes |
Various Vehicle Conditions 6 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Fan Motor | Electric fan motors operation status/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Cooling Fan High | Electric cooling fan high speed status/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Electric Cooling Fan Low | Electric cooling fan low speed status/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Idle Fuel Cut | Fuel cut at idle/
ON or OFF |
ON: Fuel cut operating | Yes |
| Diagnostic Note:
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| FC TAU | Fuel cut TAU (fuel cut during very light load)/
ON or OFF |
ON: Fuel cut operating | Yes |
| Diagnostic Note:
This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Communication with HV | Status of communication with the hybrid vehicle control ECU/
Comm or No Comm |
Comm: Power switch on (IG) | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Communication with Brake | Status of communication with the skid control ECU/
Comm or No Comm |
Comm: Power switch on (IG) | Yes |
Various Vehicle Conditions 7 (Vehicle Information)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Model Code | Model code | - | No |
| Diagnostic Note:
Used for identifying the model code: ZVW40# |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Type | Engine type | - | No |
| Diagnostic Note:
Used for identifying the engine type: 2ZRFXE |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Cylinder Number | Number of cylinders/
Min.: 0, Max.: 255 |
- | No |
| Diagnostic Note:
Used for identifying the number of cylinders: 4 |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Destination | Destination | - | No |
| Diagnostic Note:
Used for identifying the destination: W |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Model Year | Model year/
Min.: 1900, Max.: 2155 |
- | No |
| Diagnostic Note:
Used for identifying the model year: 20## |
|||
Compression (Compression)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed of Cyl #1
Engine Speed of Cyl #2 Engine Speed of Cyl #3 Engine Speed of Cyl #4 |
Engine speed for cylinder No. 1 to No. 4/
Min.: 0 rpm, Max.: 51199 rpm |
- | No |
| Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test. This is the engine speed for each cylinder measured during the engine cranking. When there is compression loss, the engine speed for that cylinder increases.
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Av Engine Speed of All Cyl | Average engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm |
- | No |
| Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test. |
|||
Various Vehicle Conditions 8 (All Data)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Requested Engine Torque | Requested engine torque/
Min.: 0 kW, Max.: 16383.75 kW |
0 to 73 kW | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| HV Target Engine Speed | HV target engine speed/
Min.: 0 rpm, Max.: 6375 rpm |
0 to 5200 rpm | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Actual Engine Torque | Actual engine torque/
Min.: -32768 Nm, Max.: 32767 Nm |
Actual engine torque | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Run Time | Engine run time/
Min.: 0 s (seconds), Max.: 255 s (seconds) |
0 to 255 s | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Request Engine Run Time | Request engine run time/
Min.: 0 s (seconds), Max.: 25.5 s (seconds) |
0 to 25.5 s | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Judge Time Engine Ignition | Judgment time for complete explosion of ignition/
Min.: 0 s (seconds), Max.: 25.5 s (seconds) |
0 to 25.5 s | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Judge Time Engine Output | Judgment time for time until engine output/
Min.: 0 s (seconds), Max.: 25.5 s (seconds) |
0 to 25.5 s | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Level | Fuel level/
Empty or Not Emp |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ISC Learning | ISC learning/
Compl or Incmpl |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| F/C for Engine Stop Req | Fuel cut for engine stop request/
ON or OFF |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Independent | Engine independent operation/
Not Opr or Operate |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Racing Operation | Racing operation/
Not Opr or Operate |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Request Warm-up | Request engine warm up/
Not Req or Request |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Independent Control | Engine independent control operation/
Not Opr or Operate |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Elec Water Pump Target Spd | Engine water pump assembly target speed/
Min.: 0 rpm, Max.: 6375 rpm |
- | Yes |
| Diagnostic Note:
Target motor speed of the engine water pump |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Elec Water Pump Spd | Engine water pump assembly speed/
Min.: 0 rpm, Max.: 6375 rpm |
- | Yes |
| Diagnostic Note:
Actual motor speed of the engine water pump |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ISC Learning Value | ISC learning value/
Min.: 0 L/s, Max.: 79.998 L/s |
0.5 to 6.1 L/s: Idling with warmed up engine (inspection mode [maintenance mode]) | Yes |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Warm up the engine.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% | ·
All fuel injectors are tested at the same time. ·
Perform the test at 3000 rpm or less. ·
Injection volume can be changed in fine gradations within control range. ·
Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and the heated oxygen sensor voltage outputs. ·
To conduct the test, enter the following menus: Active Test / Control the Injection Volume / Data List / All Data / AFS Voltage B1S1 and O2S B1S2. ·
During the Active Test, air fuel ratio feedback control and feedback learning are stopped. ·
This active test should be performed in inspection mode (maintenance mode). |
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% | ·
All fuel injectors are tested at the same time. ·
Perform the test at 3000 rpm or less. ·
Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor and the heated oxygen sensor voltage outputs. ·
To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and O2S B1S2. ·
During the Active Test, air fuel ratio feedback control and feedback learning are stopped. ·
This active test should be performed in inspection mode (maintenance mode). ·
See waveform *2 |
| Control the EGR Step Position | Open or close EGR valve | 0 to 110 steps | ·
EGR valve is fully closed at step position 0, and fully open at step position 110. ·
Amount of EGR gas flowing into the intake manifold varies in accordance with the EGR valve opening angle. ·
Perform this test when the following conditions are met: -
Vehicle is stopped. -
Engine is running. ·
Do not leave the EGR valve open for 10 seconds or more during the Active Test. ·
Be sure to return the EGR valve to step 0 when the Active Test is completed. ·
Do not open the EGR valve 30 steps or more during the Active Test. ·
This active test should be performed in inspection mode (maintenance mode). ·
See waveform *4. |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | ·
The valve is opened with a 30% duty ratio. ·
This active test should be performed in inspection mode (maintenance mode). ·
See waveform *5 |
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | Perform this test when the following conditions are met:
·
Power switch is on (IG). ·
Engine is stopped. ·
Park (P) has been selected. |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. ·
Perform this test when the following conditions are met: -
Power switch is on (IG). -
Engine is stopped. -
Park (P) has been selected. |
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | ·
Perform this test when the following conditions are met: -
Power switch is on (IG). -
Engine is stopped. -
Park (P) has been selected. ·
This active test should be performed in inspection mode (maintenance mode). |
| Control the Electric Cooling Fan | Control electric cooling fan | ON/OFF | Perform this test when the following conditions are met:
·
Power switch is on (IG). ·
Engine is stopped. ·
Park (P) has been selected. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open
Open: Throttle valve opens slowly |
Perform this test when the following conditions are met:
·
Power switch is on (IG). ·
Engine is stopped. ·
Accelerator pedal is fully depressed (accelerator pedal position: 58 degrees or more). ·
Park (P) has been selected. |
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open
Open: Throttle valve opens quickly |
·
Same as above. ·
See waveform *3 |
| Control the VVT Linear (Bank 1) | Control camshaft timing oil control valve assembly | -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance -100%: Maximum retard |
·
Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%. ·
Perform this test when the following conditions are met: -
Engine is idling. ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. ·
Test not possible with the park (P) selected during charge control. Select neutral (N) to perform test. ·
This active test should be performed in inspection mode (maintenance mode). ·
See waveform *6. |
| Control the VVT System (Bank 1) | Turn camshaft timing oil control valve on and off | ON/OFF | ·
Engine stalls or idles roughly when the camshaft timing oil control valve assembly is turned on. ·
Engine runs and idles normally when the camshaft timing oil control valve assembly is off. ·
Perform this test when the following conditions are met: -
Engine is idling. ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. ·
Test not possible with the park (P) selected during charge control. Select neutral (N) to perform test. ·
This active test should be performed in inspection mode (maintenance mode). |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | ON/OFF
#1/#2/#3/#4 |
·
This test possible when the following conditions are met: -
Vehicle is stopped. -
Engine is idling. -
Park (P) has been selected. ·
This active test should be performed in Inspection Mode (maintenance mode). |
| Control the All Cylinders Fuel Cut | Fuel cut for all cylinders | ON/OFF | ·
This test possible when the following conditions are met: -
Vehicle is stopped. -
Engine is idling. -
Park (P) has been selected. ·
This active test should be performed in inspection mode (maintenance mode). |
| Check the Cylinder Compression | Check the cylinder compression pressure | ON/OFF | This active test should be performed in inspection mode (maintenance mode).
*1 |
| Activate the Electric Water Pump | Engine water pump assembly speed control | 0 rpm/3000 rpm | Test possible when either of the following condition is met:
·
Engine coolant temperature is below 100°C (212°F). ·
Power switch on (IG) |
*1: While the Check the Cylinder Compression Active Test is being performed, if the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up.
Turn the power switch off.
Turn the power switch on (IG) and turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
Push the snapshot button to turn the snapshot function on.
Using the snapshot function, data can be recorded during the Active Test.
While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.
Crank the engine.
Monitor the engine speed (Engine Speed of Cyl #1 to #4 and Av Engine Speed of All Cyl) displayed on the GTS.
If the Check the Cylinder Compression Active Test needs to be performed after it is turned ON and performed once, press the Exit button to return to the Active Test menu screen. Then perform the Check the Cylinder Compression Active Test again.
At first, the GTS display will show each cylinder's engine speed measurement to be extremely high. After the engine has started, each cylinder's engine speed measurement will change to the actual engine speed.
As soon as the measurements are obtained, finish the Active Test.
Stop the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
Push the snapshot button to turn the snapshot function off.
Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
If the data is not displayed as a graph, the change of the values cannot be observed.
Check the change in engine speed values.
As the data values of the Active Test return to their default values when engine is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during engine running.
*2: Control the Injection Volume for A/F Sensor (Idling after warming up)
During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the Injection Volume for A/F Sensor | - | ▲A | ▲B |
| Active Test operation | -12.5% | 12.5% | |
| AFS Voltage B1S1 | 3.829 V | 2.839 V | |
| O2S B1S2 | 0.035 V | 0.955 V | |
Usually, the value of AFS Voltage B1S1 changes to less than 3.1 V when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.
Usually, the value of AFS Voltage B1S1 changes to 3.4 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
Usually, the value of O2S B1S2 changes to 0.55 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.
Usually, the value of O2S B1S2 changes to less than 0.4 V when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
*3: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Power switch on (IG))
Usually, Throttle Position Command (Target Value) and Throttle Position No. 1 (Actual Value) are almost the same.
If any DTCs related to the Electronic Throttle Control System (ETCS) are stored, this Active Test does not function.
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the ETCS Open/Close Fast Speed | - | ▲A | ▲B |
| Active Test operation | Open | Close | |
| Throttle Position Command | 2.597 V | 0.761 V | |
| Throttle Position No. 1 | 2.597 V | 0.761 V | |
| Throttle Motor Duty (Open) | 14% | 0% | |
| Throttle Motor Duty (Close) | 0% | 17% | |
*4: Control the EGR Step Position (Idling after warming up, A/C off)
| Tester Display | Measurement Item/Range | Normal Condition | |||
|---|---|---|---|---|---|
| Control the EGR Step Position | - | ▲A | ▲B | ▲C | ▲D |
| EGR Step Position | 0 step | 10 step | 20 step | 30 step | |
| MAP | 29 kPa | 31 kPa | 59 kPa | 74 kPa | |
When the value of Control the EGR Step Position is "0 step", the value of MAP should be between 20 and 40 kPa (150 to 300 mmHg).
When the EGR system is normal and the value of Control the EGR Step Position is changed from "0 step" to "30 step", the value of MAP will increase to a value at least 10 kPa (75 mmHg) higher than the value of MAP when the value of Control the EGR Step Position was "0 step".
This data is taken from an Active Test in which the step position was raised in increments of 1 step. The EGR valve inspection in the troubleshooting procedures checks the operation of the valve by stalling the engine and raises the step position in increments of 5 step.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
*5: Activate the VSV for Evap Control (Idling after warming up)
Even when the Active Test is performed (the purge VSV is opened 30%), the ECM performs air fuel ratio feedback to maintain the air fuel ratio at the stoichiometric ratio. Therefore, by observing the change in the Data List item "Injector (Port)", it is possible to determine whether the purge VSV is actually open.
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Activate the VSV for Evap Control | - | ▲A | ▲B |
| Active Test operation | ON | OFF | |
| EVAP (Purge) VSV | 29.8% | 0.0% | |
| Injector (Port) | 2267.0 μs | 2489.0 μs | |
| AFS Voltage B1S1 | 3.205 V | 3.249 V | |
The graphs and values above are for reference only because the fuel injection volume (compensation volume) varies depending on the HC density of the purge air from the canister.
*6: Control the VVT Linear (Bank 1)
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the VVT Linear (Bank 1) | - | ▲A | ▲B |
| Active Test operation* | +30% | -30% | |
| VVT Change Angle #1 | 42.9 DegFR | 0.0 DegFR | |
| VVT OCV Duty #1 | 67.0% | 7.0% | |
| VVT Aim Angle #1 | 37.0% | 37.0% | |
*: Change the control value for Control the VVT Linear to +30% or -30%.
The Control the VVT Linear (Bank 1) Active Test considers the value of VVT Aim Angle #1 to be 0 and raises or lowers the duty ratio with respect to VVT Aim Angle #1.
The sum of the control value for the Control the VVT Linear (Bank 1) Active Test and the value of VVT Aim Angle #1 is approximately equal to the value of VVT OCV Duty #1.
When the control value for the Control the VVT Linear (Bank 1) Active Test is changed a few times, there should not be a large discrepancy between VVT OCV Duty #1 when the system starts advancing or retarding the timing and the rate of change of VVT Change Angle #1.
Test not possible with park (P) selected during charge control. Select neutral (N) to perform test.