Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2019.03
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0106  Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem  


DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure as a voltage using a built-in sensor. The ECM calculates intake manifold pressure based on this voltage and also calculates the EGR valve assembly and purge VSV opening amount according to changes in the intake manifold pressure, and detects errors in the pressure sensor using the changes in pressure.

A263608E27
0.094,2.302 0.313,2.469 0.219,0.167 10 false 1.0 0.094,2.146 0.313,2.302 0.219,0.156 10 false 1.2 0.094,1.708 0.323,1.865 0.229,0.156 10 false 2.4 0.094,1.229 0.313,1.385 0.219,0.156 10 false 3.6 0.094,0.979 0.323,1.135 0.229,0.156 10 false 4.2 0.906,3.604 1.167,3.771 0.26,0.167 10 false 150 1.542,3.396 1.802,3.552 0.26,0.156 10 false 450 2.146,3.396 2.396,3.552 0.25,0.156 10 false 750 0.74,3.396 0.99,3.552 0.25,0.156 10 false 100 2.521,3.396 2.823,3.542 0.302,0.146 10 false 900 0.167,0.208 0.969,0.406 0.802,0.198 10 false Voltage (V) 0.49,4 2.25,4.198 1.76,0.198 10 false Manifold Absolute Pressure 2.49,3.615 3.229,3.813 0.74,0.198 10 false mmHg(abs) 2.719,2.99 3.313,3.229 0.594,0.24 10 false kPa(abs) 0.802,3.031 1.25,3.188 0.448,0.156 10 false 19.998 0.5,2.781 0.948,2.938 0.448,0.156 10 false 13.332 1.427,2.781 1.875,2.938 0.448,0.156 10 false 59.995 2.01,3.042 2.458,3.198 0.448,0.156 10 false 99.992 2.323,2.792 2.875,2.948 0.552,0.156 10 false 119.990

DTC No. DTC Detection Condition Trouble Area
P0106 Intake manifold pressure measured after engine start drops by less than 3 kPa (22.5 mmHg) compared to the intake manifold pressure (atmospheric pressure) measured before engine start (2 trip detection logic).
·

Intake system

·

Manifold absolute pressure sensor



MONITOR DESCRIPTION

When the intake manifold pressure measured after engine start drops by less than 3 kPa (22.5 mmHg) compared to the intake manifold pressure (atmospheric pressure) measured before engine start, the ECM interprets this as a malfunction in the manifold absolute pressure sensor and stores the DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).

8.

Move the shift lever to N.

9.

Idle the engine for 10 seconds or more [A].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

11.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0106.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO P0106)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0106 is output A
DTC P0106 and other DTCs are output B

HINT:

If any DTCs other than P0106 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (MAP)

B

2.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAP.


d.

Read the MAP value at power switch on (IG).


e.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


f.

Start the engine and warm it up.


g.

Read the MAP value at idling.

Standard:
Engine condition GTS Display
Power switch on (IG) 80 to 110 kPa(abs) [600 to 825 mmHg(abs)]
Idling (not charge control) 28 to 48 kPa(abs) [210 to 360 mmHg(abs)]




OK

NG

3.CHECK INTAKE SYSTEM
3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in the intake system.




OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

REPAIR OR REPLACE INTAKE SYSTEM