Home › Brake › BRAKE (REAR) › REAR BRAKE › from 2019.03
RM2070E _54 Brake _061926 BRAKE (REAR) _0301703 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 5.DISCONNECT REAR FLEXIBLE HOSE

a.
C244060

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 47850 6.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C414174C02
0.208,2.927 0.542,3.188 0.333,0.26 10 false *a 1.156,2.917 1.479,3.167 0.323,0.25 10 false *b
*a Hold
*b Turn


Hold the 2 rear disc brake cylinder slide pins, and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 04466 7.REMOVE REAR DISC BRAKE PAD

a.

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.

NOTICE:

When reusing the rear disc brake pads, as the shape of the inner side rear disc brake pad and outer side rear disc brake pad is different, mark each rear disc brake pad in such a way that they can be reinstalled to their original locations.



Hide 04946 8.REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.
C414901C02
0.51,1.083 0.51,1.396 false 0.927,1.302 0.927,1.604 false 2.573,2.219 2.573,2.521 false 3.031,2.49 3.031,2.792 false 1.521,2.188 1.521,2.865 false 2.146,2.563 2.146,2.656 2.146,2.656 1.521,2.656 false 0.865,1.615 1.063,1.813 0.198,0.198 10 false *1 0.427,1.406 0.656,1.646 0.229,0.24 10 false *2 1.448,2.875 1.677,3.083 0.229,0.208 10 false *3 2.5,2.542 2.75,2.781 0.25,0.24 10 false *1 2.948,2.823 3.198,3.073 0.25,0.25 10 false *2
*1 Rear No. 1 Anti-squeal Shim
*2 Rear No. 2 Anti-squeal Shim
*3 Pad Wear Indicator Plate


Remove the rear No. 1 anti-squeal shim and rear No. 2 anti-squeal shim from each rear disc brake pad.


b.

Remove the pad wear indicator plate from each rear disc brake pad.


Hide 04948 9.REMOVE REAR DISC BRAKE FITTING KIT

a.
C244053E03
0.521,0.49 0.302,0.49 false 0.448,1.292 0.281,1.292 false 1,0.479 1.188,0.479 true 0.958,1.302 1.198,1.302 true 0.104,0.406 0.281,0.563 0.177,0.156 10 false *2 0.104,1.219 0.271,1.365 0.167,0.146 10 false *1 1.188,1.229 1.365,1.385 0.177,0.156 10 true *2 1.188,0.406 1.354,0.552 0.167,0.146 10 true *1

Remove the 2 rear No. 1 disc brake pad support plates and 2 rear No. 2 disc brake pad support plates from the rear disc brake cylinder mounting.

Text in Illustration
*1 Rear No. 1 Disc Brake Pad Support Plate
*2 Rear No. 2 Disc Brake Pad Support Plate

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47814 10.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C244054

Remove the 2 rear disc brake cylinder slide pins from the rear disc brake cylinder mounting.


b.
C210924E17
2.552,0.909 2.715,1.072 0.163,0.163 10 *1 2.332,1.4 2.332,0.996 2.332,0.996 2.545,0.996 false

Using a screwdriver with its tip wrapped with vinyl tape, remove the rear disc brake cylinder slide bushing from each disc brake cylinder slide pin.

Text in Illustration
*1 Vinyl Tape

NOTICE:

Do not damage the rear disc brake cylinder slide pin.



Hide 11.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C244055

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 47722A 12.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C244056

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle beam assembly.


Hide 42491 13.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 14.REMOVE REAR DISC

a.
C232658E01
0.741,1.269 0.905,1.411 0.163,0.143 10 *a 1.688,1.408 0.93,1.354 0.93,1.354 1.661,1.354 false

Put matchmarks on the rear disc and the rear axle hub and bearing assembly.

Text in Illustration
*a Matchmark


b.
C236575

Release the parking brake and remove the rear disc.

HINT:

If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.