Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301742 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the V14 rear television camera assembly connector.

U191434E02
3.469,0.198 3.781,0.354 0.313,0.156 10 false V14


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V14-6 (CB+) - Body ground W - Body ground Power source Power switch on (ACC) 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the V14 rear television camera assembly connector.


d.

Measure the voltage and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V14-3 (CV+) - V14-2 (CV-) R - B Video signal Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
V14-5 (CGND) - Body ground W-B - Body ground Shield ground Always Below 1 V

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.

Reference (Oscilloscope waveform):

E361811E01
1,2.333 1.167,2.333 1.167,2.333 1.26,1.781 false 1.667,2.333 1.5,2.333 1.5,2.333 1.365,1.677 false 4.5,2.25 4.667,2.25 4.667,2.25 4.729,1.635 false 5.167,2.25 5,2.25 5,2.25 4.865,1.563 false 0.448,0.292 0.76,0.49 0.313,0.198 10 false *a 3.99,0.219 4.302,0.417 0.313,0.198 10 false *b 0.5,1.219 0.865,1.417 0.365,0.198 10 false GND 0.813,2.25 1.125,2.448 0.313,0.198 10 false *c 1.698,2.26 2.01,2.458 0.313,0.198 10 false *d 3.948,1.229 4.313,1.427 0.365,0.198 10 false GND 5.208,2.167 5.521,2.365 0.313,0.198 10 false *d 4.323,2.167 4.635,2.365 0.313,0.198 10 false *c

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal V14-3 (CV+) - V14-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal V14-3 (CV+) - V14-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).



Text in Illustration
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform